Kenmore Dishwasher 665.15529000 (66515529000, 665 15529000) Parts

Size: 8-32 x 1/2 inch.

This drain impeller spins inside the drain pump to move wastewater out of the appliance, restoring normal draining and reducing standing water. It's a direct-replacement pump impeller designed to fit the original pump housing. What it does:

• Drives water through the drain pump so the washer can empty properly
• Worn or broken impellers can cause slow or no draining and standing water
• May produce unusual pump noise or vibration when damaged
• Helps prevent motor overload by maintaining proper water flow

• One drain impeller

• Disconnect power before accessing the pump assembly to avoid electric shock
• Inspect the pump housing and fasteners; replace any damaged clips or seals as needed
• Reassemble pump and test a short drain cycle before completing the repair

A small mounting clip that secures interior panels or trim pieces to the appliance, keeping parts aligned and preventing rattling or movement during operation. Simple replacement restores proper fit and reduces noise from loose components. What it does:

• Holds a panel, trim or small component in place on the cabinet or housing
• Keeps parts aligned so doors, panels or covers fit and operate smoothly
• Prevents rattling or vibration caused by loose or missing fasteners
• A worn or broken clip can allow gaps, movement, or noise during use

• Disconnect power (unplug or switch off breaker) before servicing
• Replacement typically requires only basic hand tools; keep track of any removed fasteners
• Inspect surrounding mounting points and adjacent clips for wear and replace as needed

This replacement timer control knob lets you set and turn the appliance's timer with a clear grip and click-action feedback. It restores a worn or missing knob so you can reliably select time settings and operate the timer control. What it does:

• Provides a secure grip for turning the timer control and selecting time settings
• Replaces cracked, stripped, or missing timer knobs that are hard to turn
• Restores tactile click and positional indexing for accurate control
• Helps eliminate slipping or wandering of the timer pointer during use

• Install on the timer shaft by aligning the hub and pressing firmly until seated
• If knob is difficult to remove, use a flat tool gently; avoid damaging surrounding trim
• Disconnect power to the appliance before servicing timer components
• If the timer mechanism itself is damaged or nonfunctional, replace the complete timer assembly

This silverware basket replaces a cracked, broken, or missing utensil holder to keep forks, knives and spoons organized during the wash cycle. It fits into the dishwasher's lower rack and helps maintain cleaning efficiency. What it does

• Holds and separates silverware and small utensils so water and detergent can reach each piece
• Prevents nesting and keeps items upright for better cleaning and drying
• Secures loose items during the wash to avoid damage to dishes or the dishwasher
• Works with standard lower-rack mounting locations on compatible dishwashers

• One silverware basket

• Installs in the lower dishwasher rack; no tools required for typical replacements
• Position tines or compartments so utensils sit upright and do not block spray arms
• Do not overload the basket; bent or damaged tines may affect fit and function

This wheel leg is a replacement support used to stabilize and allow smooth movement of the appliance's lower assembly. It restores proper leveling and reduces wobble so the appliance sits securely and rolls or rests as designed. What it does

• Supports the appliance chassis at the lower corner and transfers load to the floor
• Helps maintain correct appliance height and leveling to reduce vibration and rocking
• Restores proper rolling or stationary support where a worn or broken leg caused instability
• Commonly replaced when the leg is cracked, stripped, missing, or no longer holds weight

• Verify appliance is unplugged and empty before accessing lower cabinet or base
• Support the appliance with a block or jack to prevent shifting while replacing the leg
• Remove any access panels or retaining hardware as needed; install the new leg in the original orientation
• Replace any fasteners that are damaged and test stability before returning the appliance to service

This pump and motor assembly circulates and drains dishwasher water to ensure proper washing and draining. It restores normal water movement so dishes get cleaned and the tub drains after a cycle. What it does:

• Circulates wash water through spray arms for effective cleaning.
• Pumps water out of the tub during drain cycles.
• Can cause noisy operation, poor cleaning, standing water, or failure to drain when defective.
• Works as the combined sump/pump motor unit used in many Whirlpool-family dishwashers.

• Disconnect power to the appliance before beginning any repair to avoid electric shock.
• Turn off the water supply and remove lower access panels to reach the pump/sump area.
• Handle as a single assembly; check and clear any debris or foreign objects from the sump and inlet before reinstalling.

This seal kit is for the main tub. It goes around the pump housing.