Kenmore Dishwasher 665.1580592 (6651580592, 665 1580592) Parts

The Lower Dishwasher Rack Assembly is an OEM part for Whirlpool dishwashers. This part holds and organizes dishes, pots, and pans in the lower section of the dishwasher, ensuring they are properly positioned for effective cleaning.

Causes of a bad lower rack can include wear and tear from regular use, exposure to harsh detergents or high temperatures, and physical damage from heavy or improperly loaded items. 

Symptoms of a bad lower dishwasher rack assembly include:

• Rust or corrosion on the rack
• Broken or missing tines
• Difficulty sliding the rack in and out
• Poor arrangement of dishes, leading to ineffective cleaning

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This seal kit is for the main tub. It goes around the pump housing.

This inlet base seal is a gasket that fits between the inlet base and its mating surface. Replacing a worn seal helps maintain proper airflow through the inlet path and keeps spills and debris out of internal components.

• Forms a tight, continuous seal at the inlet base-to-housing joint
• Helps preserve correct airflow through the inlet path
• Blocks liquids, grease, and crumbs from leaking into the appliance interior
• Replace if the seal is cracked, flattened, brittle, loose, or you see visible gaps

• Disconnect power to the appliance before servicing
• Remove grates/cartridges, filters, or trim as needed to access the inlet base
• Clean and dry mating surfaces; install the new seal in the same orientation without stretching or twisting
• Reassemble and verify the seal sits evenly with no gaps

This replacement silverware basket holds forks, knives and spoons in the dishwasher lower rack so utensils stay upright and separate for better cleaning and easier unloading. It's a direct-fit interior basket designed to restore secure utensil loading. What it does:

• Keeps silverware and small utensils contained so pieces don't fall through or block the spray arms
• Separates items to improve water flow and cleaning coverage
• Prevents loose utensils from banging and potentially damaging dishes
• Replaces cracked, broken, or missing baskets that allow utensils to shift during the cycle

• Drop into the lower rack — no tools required for typical swap-out
• Position basket so it sits flat and does not interfere with rack movement or spray arm rotation
• Avoid overloading; place sharp utensils point-down or bundle separately to reduce hazard when unloading
• For appliance repairs beyond simple replacement, disconnect power and water before servicing

Bottle with brush. Color: Platinum. Size: 0.6 fl.oz.

Screw for wash impeller.

This door spring retainer secures the dryer/washer door spring to the cabinet so the hinge spring stays in place for reliable door movement and alignment. It prevents the spring from slipping or disengaging during normal use. What it does:

• Holds the door spring end in the correct position so the hinge maintains proper tension
• Helps prevent door sagging, misalignment, or a door that won't stay closed
• Keeps the spring secured to reduce rattling or intermittent disengagement
• Works with the existing door hinge/spring assembly to restore reliable opening and closing

• Disconnect power (and gas if applicable) before any service; wear gloves and eye protection
• Access typically requires opening or removing the dryer/washer front or top panel; follow OEM service manual for steps
• Retaining springs are under tension—carefully release and re-seat springs to avoid sudden movement
• If other hinge or spring hardware is damaged, replace those parts to ensure safe operation

For mating plug use 691707.

This electrical terminal connects a wire to a matching male/female connector on the appliance, restoring a secure circuit connection and helping prevent intermittent power or signal loss. Use when a damaged or corroded terminal causes poor contact. What it does:

• Provides a secure electrical connection between a wire and the appliance wiring harness or component
• Replaces bent, corroded, or loose terminals that can cause intermittent operation or no power to a component
• Restores reliable contact to prevent arcing and heat buildup at the connection
• Works with compatible wire gauges and mating connectors to maintain circuit continuity

• Disconnect power to the appliance before inspecting or replacing terminals to avoid shock or injury
• Verify wire routing and match the terminal orientation before crimping or installing
• Use proper crimping or soldering techniques and the correct-size terminal for the wire gauge
• Inspect mating connectors and replace any that are damaged or corroded for a long-lasting repair