Kenmore Dishwasher 665.15824000 (66515824000, 665 15824000) Parts

This adjustable leveling leg threads into the appliance base to set height and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking and vibration and helps maintain proper alignment for reliable operation.

• Provides adjustable support at one corner of the appliance
• Helps level the unit for correct alignment with floor or cabinetry
• Reduces rocking, vibration, and rattling noises
• Replaces stripped, bent, cracked, or missing leg

• Disconnect power and, if applicable, shut off water before servicing
• Carefully support or brace the appliance to access the base safely
• Start the new leg by hand to avoid cross-threading; adjust height gradually
• Use a level to check side-to-side and front-to-back, then recheck after positioning

This vent screen covers the dishwasher door vent, allowing steam to escape while blocking food particles and debris. Replacing a damaged or missing screen helps maintain proper airflow and can reduce moisture and odors around the vent area.

• Screens the door vent to keep debris out of the vent duct and fan path
• Maintains airflow for venting steam during the dry cycle
• A clogged, cracked, or missing screen may lead to moisture at the vent, odors, or reduced drying performance
• Replace if warped, broken, or lost during service

• Disconnect power to the dishwasher at the breaker before servicing
• Open the door and remove inner-door screws to access the vent assembly
• Remove the old screen, seat the new screen fully and evenly, then reassemble without overtightening
• Run a short cycle and check the vent area for proper airflow and moisture

Comes with seal.

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

Size: 8-18 x 1/2 inch.

Touch-up paint for repairing small chips, scratches and scuffs on painted appliance surfaces. Restores the appearance of localized damage so repaired areas better blend with the surrounding finish. What it does:

• Covers small chips and surface scratches to improve cosmetic appearance.
• Helps conceal finish wear on painted metal and plastic trim.
• Lets you spot-repair without replacing large panels or parts.
• Works for quick, visible fixes where full repainting isn't needed.

• Clean and dry the repair area thoroughly before applying; remove loose paint or rust.
• Test on an inconspicuous area first to confirm color match and compatibility.
• Apply sparingly in thin coats with a small brush or cotton swab; allow each coat to dry before adding more.
• Use in a well-ventilated area and keep out of reach of children; follow any handling instructions on the product label.

A threaded screw used to secure appliance components where an 8-16 thread is specified. Provides a straightforward replacement fastener to restore original fit and keep panels, brackets, and internal parts held securely. What it does:

• Fastens panels, brackets, trim, and small assemblies that use an 8-16 threaded fastener.
• Replaces missing, corroded, stripped, or damaged screws to stop rattling, gaps, or loose parts.
• Restores reliable mechanical connection after service or part replacement.
• Compatible where the OEM specifies an 8-16 screw for mounting or securing components.

• Use the correct driver to avoid stripping the head; start threads by hand to prevent cross-threading.
• Tighten until secure but avoid over-tightening to prevent damage to mounting holes or plastic parts.
• If working near electrical components, disconnect power and follow all safety precautions.
• Inspect mating threads and replace if damaged before installing this screw.

Complete drain pump and motor assembly that removes water from the washer during drain cycles, restoring reliable draining and preventing standing water for trouble-free spin and dry cycles. What it does:

• Pumps water out of the washer tub during drain cycles to help the washer complete drain and spin operations.
• Helps address common symptoms like a washer that won't drain, leaves water in the tub, or makes grinding/humming noises from the pump area.
• Replaces the original drain pump/motor unit to restore normal pump operation when the old unit is worn, clogged, or failing.

• One pump and motor assembly.

• Disconnect power and shut off water to the appliance before beginning any service.
• Drain any remaining water from the tub or hoses to avoid spills; keep towels or a shallow pan handy.
• Note or photograph hose and wiring connections before removal to ensure correct reassembly.
• Inspect pump mounting gaskets, hose clamps and hoses; replace damaged seals to prevent leaks.

This push retainer is a small press-on fastener that secures components to shafts or studs inside your appliance. It restores a tight, reliable hold so knobs, trim, or linkages don't loosen or fall off during use. What it does:

• Presses onto a shaft or stud to secure knobs, trim, or linkages—no threads required
• Maintains spring tension to resist vibration during normal operation
• Replaces a missing, bent, or weakened retainer
• Common symptoms: loose or wobbly knobs/trim, parts slipping off, or a retainer that won't stay on

• 1 push retainer

• Disconnect power; for gas appliances, also shut off the gas supply
• Access the shaft/stud and carefully remove the old retainer with pliers; avoid damaging adjacent plastic parts
• Press the new retainer on squarely using a deep socket or nut driver; do not hammer directly
• If the mating shaft or component is damaged or deformed, address that before installing the new retainer

A pronged cup washer that secures and cushions mating parts on appliances, restoring proper fit and reducing wobble. Replaces worn or damaged cup-style washers to help maintain stable component alignment and reliable operation. What it does:

• Fits into a cup or socket to hold shafts, knobs, or trim pieces in place
• Pronged design grips the mounting surface to prevent rotation and slippage
• Helps reduce vibration and noise caused by loose or worn washers
• Commonly used when a knob, shaft, or trim feels loose or wobbly

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove the related knob or trim carefully to access the washer; note orientation for correct reassembly
• Press the washer fully into the cup or socket so the prongs engage the mounting surface
• Inspect the surrounding components for wear and replace any damaged parts

Color: Biscuit. Size: 13 oz. can. Enamel spray paint.

Size: 8-32 x 1/2 inch.

This wet agent dispenser assembly holds and releases liquid wetting/conditioning agents into the wash at the correct cycle, helping deliver fabric conditioner or similar additives when needed. It replaces a worn, clogged, or damaged dispenser for reliable delivery. What it does:

• Holds liquid fabric conditioner/wetting agent and releases it into the tub during the rinse cycle
• Ensures timed dispensing so conditioners are added at the proper point in the cycle
• Helps prevent over-dispensing and visible residue in the washer tub or on clothes
• Commonly replaces dispensers that leak, fail to release liquid, or have broken mounting tabs

• One wet agent dispenser assembly

• Disconnect power to the appliance before beginning any work
• Remove and reinstall using basic hand tools
• Rinse any remaining liquid from the area and avoid skin/eye contact with chemicals
• Test a short cycle after installation to ensure proper dispensing and secure mounting

This wheel and bearing assembly mounts to the upper dishrack, allowing it to glide smoothly in and out on the rail. Replacing a worn or broken wheel restores smooth operation and helps keep the rack securely on track.

• Supports and guides the upper rack along the side rails
• Restores smooth rolling and proper rack alignment
• Helps prevent the rack from binding or derailing
• Common symptoms: rack hard to slide, falls off track, wheel cracked/missing, squeaking or grinding as the rack moves

• Disconnect power before servicing; remove the upper rack from the rails by releasing the rack stops
• Release the old wheel/bearing from the rack tabs and remove
• Snap the new assembly into the rack mounting holes until it locks
• Reinstall the rack and verify smooth travel on both rails

This wheel leg is a replacement support used to stabilize and allow smooth movement of the appliance's lower assembly. It restores proper leveling and reduces wobble so the appliance sits securely and rolls or rests as designed. What it does

• Supports the appliance chassis at the lower corner and transfers load to the floor
• Helps maintain correct appliance height and leveling to reduce vibration and rocking
• Restores proper rolling or stationary support where a worn or broken leg caused instability
• Commonly replaced when the leg is cracked, stripped, missing, or no longer holds weight

• Verify appliance is unplugged and empty before accessing lower cabinet or base
• Support the appliance with a block or jack to prevent shifting while replacing the leg
• Remove any access panels or retaining hardware as needed; install the new leg in the original orientation
• Replace any fasteners that are damaged and test stability before returning the appliance to service