Kenmore Dishwasher 665.16052400 (66516052400, 665 16052400) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: 8533949
$45.95
- Compare At:
-
$54.68
- You Save:
-
$8.73
Out Of Stock
Usually ships within 4 - 14 days
Genuine Whirlpool part
By: Whirlpool
Part Number: 8557504
$47.27
- Compare At:
-
$55.78
- You Save:
-
$8.51
Out Of Stock
Usually ships within 4 - 14 days
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3400931
The Whirlpool push on retainer nut is an OEM replacement part responsible for securing the heating element in the dishwasher. It is located in the base of the dishwasher's tub to hold the heating element firmly in place. The push-on retainer nut keeps the heating element securely connected to the dishwasher's electrical system while allowing for easy removal and replacement when necessary.
Over time, push on retainer nuts can become loose, worn out, or damaged due to regular use, vibrations, or accidental mishandling. If a retainer nut fails, it can lead to parts becoming unstable or disconnected.
Symptoms of a bad push on retainer nut include:
- Loose or unstable dishwasher components
- Parts falling off or becoming misaligned
- Unusual noises during the wash cycle
- Difficulty in securing components within the dishwasher
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models
Do-It-Yourself Stories from Customers like You
Our dishwasher would not start. Rory D. • Fairfield , CA • May 18, 2020
A bit of searching on the internet narrowed the problem down to either the heating element or the control board. As I am not much of a diagnostician I decided to replace both. Along this same line, I would never have attempted these repairs if it hadn't been for the clear, easy to understand repair videos provided for each part. Further, my decision to do my own repairs was made easier because the prices of the parts was so reasonable.
I took my time, reviewed the videos and replaced the...
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP661658
The Dishwasher Drain Pump is an OEM part for Whirlpool dishwashers. It is responsible for removing water from the dishwasher at the end of each cycle, ensuring that dishes are properly cleaned and dried.
Causes of a bad drain pump can include wear and tear from regular use, blockages from debris, or electrical malfunctions.
Symptoms of a bad drain pump include:
- Water not draining from the dishwasher
- Unusual noises during the drain cycle
- Error codes related to drainage issues
- Water pooling at the bottom of the dishwasher
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Dishwasher drain pump not working Steve E. • Tampa , FL • January 14, 2015
When the wife told me the dishwasher was leaving water in the bottom of the tub I hoped it'd be that the filter was just clogged. Nope. We usually clean our dishes before cleaning them which always makes me laugh but the drain was clear after 9 years of use, so I figured it was the pump. This was a $200 minimum for the appliance guy to replace, so I thought I'd try and do it myself.
Job wasn't too bad. Found a youtube video from another machine than mine which I hoped would help.. these...
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8269208
Do-It-Yourself Stories from Customers like You
Would not complete a cycle the clean light would flash seven times indicating a faulted heater circuit ohm check good on the element thermistor would not open a 75 to 80 deg Ralph B. • Watauga , TX • October 21, 2016
Unplug the old twist remove. Push the new one in twist,plug the wires in. Flop around on floor under sink to hook every thing up.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8268332
Do-It-Yourself Stories from Customers like You
Dishwasher not getting dishes clean Charlie C. • Alna , ME • August 27, 2017
Replaced upper and lower spray arms and a few other parts.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: 4392900
Color: Biscuit. Size: 1 qt. can uncut. Enamel paint.
More
Genuine Whirlpool part
By: Whirlpool
Part Number: 8171555
Genuine Whirlpool part
By: Whirlpool
Part Number: 8542575
Maybe referred to as Soil Sensor.
More
Genuine Whirlpool part
By: Whirlpool
Part Number: 8558955
Do-It-Yourself Stories from Customers like You
Bad control panel Michael L. • Riverdale , MD • November 13, 2014
The control panel on my brand of Kenmore dishwasher goes bad every couple years. In the past, we've renewed the SEARS warranty, but it just didn't seem to make sense financially. Thankfully, shops like AppliancePartsPros.com exist. I find the part I needed... about $30-$40 cheaper than buying direct from SEARS. Part arrived in about 3 days. Works as expected.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: W10348405
Genuine Whirlpool part
By: Whirlpool
Part Number: W10586592
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3370389
Size: 10-32 x 15/16 inch.
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8268983
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8269632
Color: Black
Do-It-Yourself Stories from Customers like You
Broken latch handle Allen H. • Philadelphia , PA • March 25, 2014
Replaced broken part. This was a simple fix. The only complication was that SEARS sent me the WRONG PART THREE TIMES and the first part they sent WAS BROKEN. I found these guys on line, found the part by number, looked at a photograph instead of crappy drawing, and had the part in three days. Should have come here first.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8534882
Seal included. This sump housing assembly includes a 31-31.5 millimeter hole for the thermistor. If the hole for the thermistor is 32.17 millimeters you will need to order WP8572618.
More