Kenmore Dishwasher 665.16264400 (66516264400, 665 16264400) Parts

This thermostat bracket holds the oven or range thermostat securely in place, ensuring accurate temperature sensing and stable oven performance. Replaces a worn or broken bracket to restore proper thermostat positioning. What it does:

• Secures the thermostat assembly to the oven/range interior so the thermostat bulb or probe senses temperature correctly
• Prevents the thermostat from shifting or contacting heating elements
• Commonly replaced when the bracket is cracked, bent, or missing and causes temperature or control issues
• Helps reduce temperature inconsistencies caused by a loose or damaged mounting

• Disconnect power to the appliance before servicing to avoid electrical shock or injury
• Handle the thermostat and sensor bulb carefully; avoid kinks or direct pressure on sensing elements
• Basic hand tools are typically required; verify part alignment before tightening fasteners

This push-in retainer secures panels, trim or light-weight components inside the appliance to prevent vibration and movement during operation. It's a small, low-profile fastener that snaps into a pre-drilled hole for a clean, tool-free hold. What it does:

• Holds interior trim, access panels or wiring looms in place to reduce rattles and movement
• Replaces worn or broken plastic retainers that no longer grip securely
• Helps maintain proper alignment of lightweight components for reliable operation
• Can prevent loose parts from contacting moving components

• Disconnect power to the appliance before starting any work
• Access the area and remove any surrounding trim or panels as needed
• Align retainer with the hole and push straight in until it snaps or seats flush
• Inspect fit after installation; replace if damaged or does not secure properly

This positioner adjustment arm helps hold and guide the appliance component so it moves into the correct position during operation, restoring proper alignment and reducing noise or mis-positioning. What it does:

• Secures and guides the linked mechanism so parts engage in the correct position
• Helps prevent off-center movement, binding, and unusual noises during cycles
• Restores correct positioning when a worn or broken arm causes misalignment
• Works as a direct-replacement service part for the original positioner linkage

• Disconnect power (and water/gas if applicable) before beginning any repairs
• Inspect related linkage, fasteners, and mounting points for wear or damage and replace if needed
• Reassemble carefully so linkage moves freely through its full range of motion

This loose bag assembly is a direct-fit replacement designed to restore the original containment or collection function in compatible Whirlpool appliances. It provides a simple swap to fix a damaged or missing bag and keep the appliance operating as intended. What it does:

• Replaces a worn, torn, or missing bag used for containment or collection in the appliance
• Restores proper collection and helps prevent debris or material from escaping into the appliance cavity
• Helps reduce related performance issues that occur when the bag is damaged or absent
• Matches OEM form and fit for an easy, reliable replacement

• One loose bag assembly as shown

• Turn off and unplug the appliance before attempting replacement
• Remove any panels or components required to access the bag
• Install the bag in the correct orientation and secure all fasteners or clips
• Inspect surrounding seals and openings; replace any damaged parts to ensure proper operation

This adjuster is a replacement door/hinge adjustment component that restores proper door alignment and closing action for compatible appliances. It helps re-establish correct clearance and reduces rubbing, binding, or uneven gaps. What it does:

• Provides the adjustment point for proper door alignment and smooth operation
• Helps correct doors that sit unevenly, rub, or don't seal consistently
• Restores the ability to fine-tune door position after hinge or cabinet repairs
• Reduces noise and wear caused by misaligned doors or panels

• One adjuster as shown

• Turn power off and disconnect the appliance before starting any repair
• Some disassembly of the door, hinge, or trim may be required
• Keep fasteners and small parts organized; verify orientation before final tightening

A flat washer used with fasteners on select top-load and front-load washer assemblies to distribute load and prevent loosening. Replaces worn or missing washers to help stabilize mounting points and reduce vibration where metal parts join. What it does:

• Provides a smooth bearing surface between a bolt or nut and the mating part
• Helps distribute clamping force to prevent damage to housings or panels
• Reduces loosening from vibration or thermal cycling
• Common fix when mounting hardware is loose, rattling, or causing leaks at joins

• Inspect mating bolt, nut, and surface for wear or damage before installing
• Use correct size and orientation; do not overtighten fasteners
• Disconnect power to the appliance and follow safety procedures when accessing internal parts
• Replace all related fasteners to ensure proper fit

The Door Hinge (RH) is an OEM replacement part for Whirlpool dishwashers. This hinge is installed on the right-hand side of the dishwasher door, allowing it to open and close smoothly while maintaining the proper tension and alignment. The hinge plays a crucial role in ensuring the door seals securely during operation, preventing leaks and enabling efficient cleaning performance.

Common causes include regular use leading to wear and tear, accidental impacts, or exposure to moisture, which can contribute to rust or corrosion.

Symptoms of a bad door hinge include:

• The dishwasher door not closing completely
• Difficulty opening or closing the door
• A sagging or misaligned door
• Unusual noises when moving the door

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Circulation Motor is an OEM part for Whirlpool dishwashers. It is responsible for pumping water through the spray arms to ensure thorough cleaning of dishes during the wash cycle. This motor helps maintain consistent water pressure and flow, crucial for effective dishwashing performance.

Over time, the circulation motor can fail due to factors such as motor wear, electrical issues, or blockages that cause the motor to overheat or become damaged. Regular use and the buildup of debris or hard water deposits can also contribute to motor failure.

Symptoms of a bad circulation motor include:

• Poor cleaning results
• Unusual noises during the wash cycle
• Water not circulating properly
• Dishwasher not completing cycles

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Detergent Dispenser Assembly is an OEM part for Whirlpool dishwashers, designed to store and release detergent and rinse aid at the appropriate times during the wash cycle. This component ensures that your dishes are cleaned efficiently by dispensing the correct amount of detergent for optimal washing performance. 

Causes of a malfunctioning dispenser can include mechanical failure of the latch or spring mechanism, clogging due to detergent buildup, or electrical issues preventing the dispenser from operating correctly.

Symptoms of a bad Detergent Dispenser Assembly include:

• Detergent not being dispensed correctly, leading to poorly cleaned dishes.
• The dispenser door not opening during the cycle or failing to latch properly before starting.
• Leakage of detergent from the dispenser, indicating a seal failure.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Water Supply Tube is an OEM component specifically designed for connecting Whirlpool brand dishwashers to home plumbing systems. It transports water into dishwashers for cleaning and rinsing cycles.  

Potential causes of a problematic supply tube include mineral deposits reducing flow or small punctures from prolonged vibrations.

Symptoms of a faulty water supply tube include:

• Water leaks inside or underneath the dishwasher
• Inadequate water pressure impacting clean performance

Compatible models include some brands produced by KitchenAid, Maytag, and Kenmore.

Color: Black - Part has been changed to an Access Panel Kit - The toe panel is no longer used.

This push-in screw cover conceals exposed fasteners or open screw holes on your appliance for a clean, finished look. It snaps into place to hide hardware and help keep dust and splashes out of the opening.

• Conceals visible screw heads or open screw holes on panels, doors, or trim
• Helps block dust and moisture from entering the opening
• Restores appearance when the original cap is missing or damaged
• Common symptoms: missing cap, cracked or loose cover, visible fastener or hole

• Align the cap with the hole and press in until fully seated and flush
• Clear any debris or old cap fragments from the hole to ensure a secure fit

This pump sump screen filters lint, debris and small objects from wash water before it reaches the drain pump, helping prevent clogs and pump damage. Replace a cracked or clogged screen to restore proper draining. What it does:

• Captures lint, coins, hair and small debris before the drain pump
• Helps prevent pump blockages that cause poor draining or standing water
• Reduces wear on the drain pump by stopping larger debris
• Improves overall drain performance when the existing screen is damaged or clogged

• Disconnect power and water before accessing the pump area
• Remove the washer access panel or cabinet per your model's service instructions to reach the sump
• Inspect and clean surrounding areas and the pump inlet when replacing the screen

Color: Biscuit. Screw for lower toe panel. For black screw use WP302868, for white screw use WP3400836.