Kenmore Dishwasher 665.16483300 (66516483300, 665 16483300) Parts

This loose bag assembly is a direct-fit replacement designed to restore the original containment or collection function in compatible Whirlpool appliances. It provides a simple swap to fix a damaged or missing bag and keep the appliance operating as intended. What it does:

• Replaces a worn, torn, or missing bag used for containment or collection in the appliance
• Restores proper collection and helps prevent debris or material from escaping into the appliance cavity
• Helps reduce related performance issues that occur when the bag is damaged or absent
• Matches OEM form and fit for an easy, reliable replacement

• One loose bag assembly as shown

• Turn off and unplug the appliance before attempting replacement
• Remove any panels or components required to access the bag
• Install the bag in the correct orientation and secure all fasteners or clips
• Inspect surrounding seals and openings; replace any damaged parts to ensure proper operation

This adjuster is a replacement door/hinge adjustment component that restores proper door alignment and closing action for compatible appliances. It helps re-establish correct clearance and reduces rubbing, binding, or uneven gaps. What it does:

• Provides the adjustment point for proper door alignment and smooth operation
• Helps correct doors that sit unevenly, rub, or don't seal consistently
• Restores the ability to fine-tune door position after hinge or cabinet repairs
• Reduces noise and wear caused by misaligned doors or panels

• One adjuster as shown

• Turn power off and disconnect the appliance before starting any repair
• Some disassembly of the door, hinge, or trim may be required
• Keep fasteners and small parts organized; verify orientation before final tightening

This rinse aid sensor detects the presence/level of rinse aid and signals the dishwasher control so the dispenser and cycle logic respond correctly. Replaces a failed sensor to restore proper rinse-aid detection. What it does

• Acts as a reed-style sensor that notifies the control when rinse aid is present
• Helps the dispenser and control board make rinse-aid–related decisions
• Commonly replaced when rinse-aid indicators fail or rinse-aid detection errors occur
• Small, low-voltage sensing device used in the dishwasher dispenser area

• One rinse aid sensor (reed switch)

• Disconnect power to the appliance before starting any service
• Access may require removing the door inner panel or dispenser assembly; follow the service manual
• Handle gently and avoid bending the sensor leads; ensure secure electrical connections

Color: Bisque

This replacement cupshelf mount clip secures the cup shelf/bin inside the refrigerator door so items stay stable and the shelf functions correctly. Durable plastic clip restores proper shelf alignment and retention. What it does

• Secures the cup shelf/bin to the refrigerator door so the shelf stays in place.
• Helps prevent the door shelf from tilting or falling when loaded.
• Restores proper engagement when the original clip is cracked, broken, or missing.

• One mount cupshelf clip.

• Unload the door shelf/bin before replacing the clip to avoid dropped items.
• Typically snaps into place—align the clip and press until it seats; use a flat tool only if needed.
• Inspect adjacent door components for damage and replace any worn parts for best fit.

A flat washer used with fasteners on select top-load and front-load washer assemblies to distribute load and prevent loosening. Replaces worn or missing washers to help stabilize mounting points and reduce vibration where metal parts join. What it does:

• Provides a smooth bearing surface between a bolt or nut and the mating part
• Helps distribute clamping force to prevent damage to housings or panels
• Reduces loosening from vibration or thermal cycling
• Common fix when mounting hardware is loose, rattling, or causing leaks at joins

• Inspect mating bolt, nut, and surface for wear or damage before installing
• Use correct size and orientation; do not overtighten fasteners
• Disconnect power to the appliance and follow safety procedures when accessing internal parts
• Replace all related fasteners to ensure proper fit

The Door Hinge (RH) is an OEM replacement part for Whirlpool dishwashers. This hinge is installed on the right-hand side of the dishwasher door, allowing it to open and close smoothly while maintaining the proper tension and alignment. The hinge plays a crucial role in ensuring the door seals securely during operation, preventing leaks and enabling efficient cleaning performance.

Common causes include regular use leading to wear and tear, accidental impacts, or exposure to moisture, which can contribute to rust or corrosion.

Symptoms of a bad door hinge include:

• The dishwasher door not closing completely
• Difficulty opening or closing the door
• A sagging or misaligned door
• Unusual noises when moving the door

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Circulation Motor is an OEM part for Whirlpool dishwashers. It is responsible for pumping water through the spray arms to ensure thorough cleaning of dishes during the wash cycle. This motor helps maintain consistent water pressure and flow, crucial for effective dishwashing performance.

Over time, the circulation motor can fail due to factors such as motor wear, electrical issues, or blockages that cause the motor to overheat or become damaged. Regular use and the buildup of debris or hard water deposits can also contribute to motor failure.

Symptoms of a bad circulation motor include:

• Poor cleaning results
• Unusual noises during the wash cycle
• Water not circulating properly
• Dishwasher not completing cycles

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Detergent Dispenser Assembly is an OEM part for Whirlpool dishwashers, designed to store and release detergent and rinse aid at the appropriate times during the wash cycle. This component ensures that your dishes are cleaned efficiently by dispensing the correct amount of detergent for optimal washing performance. 

Causes of a malfunctioning dispenser can include mechanical failure of the latch or spring mechanism, clogging due to detergent buildup, or electrical issues preventing the dispenser from operating correctly.

Symptoms of a bad Detergent Dispenser Assembly include:

• Detergent not being dispensed correctly, leading to poorly cleaned dishes.
• The dispenser door not opening during the cycle or failing to latch properly before starting.
• Leakage of detergent from the dispenser, indicating a seal failure.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Color: Black - Part has been changed to an Access Panel Kit - The toe panel is no longer used.

Color: Stainless

This pump sump screen filters lint, debris and small objects from wash water before it reaches the drain pump, helping prevent clogs and pump damage. Replace a cracked or clogged screen to restore proper draining. What it does:

• Captures lint, coins, hair and small debris before the drain pump
• Helps prevent pump blockages that cause poor draining or standing water
• Reduces wear on the drain pump by stopping larger debris
• Improves overall drain performance when the existing screen is damaged or clogged

• Disconnect power and water before accessing the pump area
• Remove the washer access panel or cabinet per your model's service instructions to reach the sump
• Inspect and clean surrounding areas and the pump inlet when replacing the screen

A small replacement retainer that secures the FlexRow assembly so the component stays aligned and stable during use. Replacing a worn or broken retainer restores proper positioning and reduces movement. What it does:

• Holds the FlexRow assembly in place to prevent shifting or sagging
• Helps maintain correct alignment for even operation
• Stops clicking, rubbing, or intermittent contact caused by a loose assembly
• Prevents additional wear on adjacent clips or mounts

• Disconnect power to the appliance before beginning any repair
• Removal usually requires releasing adjacent clips or fasteners; basic hand tools may be needed
• Inspect surrounding parts and replace any damaged clips or mounts for a secure fit

Color: Biscuit. Screw for lower toe panel. For black screw use WP302868, for white screw use WP3400836.