Kenmore Dishwasher 665.1743590 (6651743590, 665 1743590) Parts

Float that detects and communicates water level to the appliance control so the washer or dishwasher can fill and drain properly. Replaces a cracked, stuck, or worn float to restore reliable water sensing. What it does:

• Senses water level and relays position to the machine's control system.
• Helps prevent overfilling or unintended continuous filling when working correctly.
• Can resolve symptoms such as flooding, constant filling, no fill, or improper drain cycles.
• Works with the appliance's existing valve and switch components to re-establish normal fill/drain operation.

• Disconnect power (and water supply where applicable) before beginning service.
• Remove outer panels or tub shroud to access the float; use basic hand tools.
• Handle clips and fittings gently; do not force plastic tabs or connectors during removal/installation.
• After installation, restore power and run a test cycle to ensure correct fill and drain behavior.

Split-ring seal designed to secure a door or panel gasket and maintain a watertight/airtight joint, helping stop leaks and keep the appliance operating properly. Ideal for replacing worn or damaged seals. What it does:

• Holds and seals the gasket or trim in place to prevent water or air from escaping.
• Restores a tight seal around doors, panels or openings that show gaps or wear.
• Helps stop common symptoms like leaking, moisture buildup, or visible gaps at the seam.
• Keeps components aligned so doors close smoothly and seals wear evenly.

• Always disconnect power and turn off the water supply before starting any repair.
• Use hand tools to remove trim or retaining rings carefully; wear gloves to protect hands from sharp edges.
• Inspect surrounding gasket and mounting surface; replace damaged gaskets and clean mating surfaces before installing the new ring.
• After installation, test the appliance for proper seal and operation.

This package contains one roller. To order a set of 4 use 4317933.

Color: White. Size: 13 oz. Spray paint primer. can.

This disk mount is a small replacement mounting disk that secures and aligns internal components so the appliance operates quietly and reliably. It restores proper fit where a worn or damaged mount causes misalignment or vibration. What it does:

• Provides a secure mounting point for internal assemblies and helps maintain correct component alignment
• Reduces vibration and rattling caused by a broken or deteriorated mount
• Supports stable operation and prevents excess wear on adjoining parts
• Commonly replaced when mount is cracked, warped, or missing

• One disk mount as shown

• Basic hand tools typically required; inspect surrounding components for damage before reassembly
• Disconnect power and/or gas and follow appliance safety procedures before starting work
• Retain all fasteners and observe correct orientation during installation

This replacement caster and socket assembly restores smooth rolling and stable support for the appliance cabinet. Use it to replace a worn or damaged wheel and mounting socket so the appliance moves easily and sits level. What it does:

• Provides a rolling wheel and mounting socket to support appliance movement and weight.
• Replaces cracked, seized, or worn casters that cause dragging, sticking, or uneven motion.
• Helps reduce noise and cabinet scuffs from a damaged or loose wheel.
• Restores proper alignment when the appliance tilts or does not roll smoothly.

• Disconnect power and water and move the appliance to a safe, stable work area before starting.
• Support the appliance to prevent tipping when removing/installing the caster.
• Remove any trim or mounting hardware covering the caster; match orientation and fasteners when installing the replacement.
• After installation, verify the appliance rolls smoothly and sits level; tighten fasteners as needed.

This dishwasher air gap prevents backflow from the sink into the dishwasher drain line, helping keep wastewater out of the appliance and reducing odors. It provides a simple, code-friendly way to vent the drain hose at the sink. What it does:

• Creates an air break in the dishwasher drain to prevent soiled water from flowing back into the machine
• Helps the dishwasher drain properly and reduces standing water in the tub or sink
• Reduces odors and contamination risk caused by backflow through the drain hose
• Works with most standard sink-mount dishwasher drain hose setups

• Designed for sink-mount installation; follow sink and dishwasher manufacturer instructions and local plumbing codes
• Use appropriate hose clamps and a secure hose connection to prevent leaks
• Inspect and clean the air gap periodically to remove debris

This wheel leg is a replacement support used to stabilize and allow smooth movement of the appliance's lower assembly. It restores proper leveling and reduces wobble so the appliance sits securely and rolls or rests as designed. What it does

• Supports the appliance chassis at the lower corner and transfers load to the floor
• Helps maintain correct appliance height and leveling to reduce vibration and rocking
• Restores proper rolling or stationary support where a worn or broken leg caused instability
• Commonly replaced when the leg is cracked, stripped, missing, or no longer holds weight

• Verify appliance is unplugged and empty before accessing lower cabinet or base
• Support the appliance with a block or jack to prevent shifting while replacing the leg
• Remove any access panels or retaining hardware as needed; install the new leg in the original orientation
• Replace any fasteners that are damaged and test stability before returning the appliance to service

This support bearing assembly stabilizes the dryer drum and helps it spin smoothly to improve tumbling and reduce noise. Designed to replace a worn or noisy rear drum support for compatible Whirlpool dryers. What it does:

• Supports the rear of the dryer drum so it rotates evenly
• Reduces squeaks, grinding, and wobbling caused by worn bearings
• Helps maintain proper drum alignment to prevent uneven wear
• Works with the drum shaft to keep tumbling smooth during operation

• One support bearing assembly

• Disconnect power before beginning any repair to avoid electrical shock
• Access may require removing the dryer rear panel and drum; follow manufacturer service instructions
• Inspect adjacent components and replace if excessively worn
• Tighten fasteners to manufacturer torque specs and test operation after reassembly

The Lower Dishwasher Rack Assembly is an OEM part for Whirlpool dishwashers. This part holds and organizes dishes, pots, and pans in the lower section of the dishwasher, ensuring they are properly positioned for effective cleaning.

Causes of a bad lower rack can include wear and tear from regular use, exposure to harsh detergents or high temperatures, and physical damage from heavy or improperly loaded items. 

Symptoms of a bad lower dishwasher rack assembly include:

• Rust or corrosion on the rack
• Broken or missing tines
• Difficulty sliding the rack in and out
• Poor arrangement of dishes, leading to ineffective cleaning

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.