Kenmore Dishwasher 665.17749K010 (66517749K010, 665 17749K010) Parts

An electronic control board that manages cycle selection, timing and user controls so your appliance responds correctly to settings and sensor input. Replacing a faulty board restores reliable control and cycle operation. What it does:

• Acts as the appliance's brain, sending power and signals to motors, valves and sensors
• Interprets user commands from the console and starts or advances cycles
• Controls timers, display readouts and cycle logic based on sensor feedback
• Can stop erratic behavior caused by shorted or failed circuitry (unresponsive buttons, cycles that won't start or stop, or incorrect cycle selection)

• Disconnect power before starting; work only with the appliance fully de-energized
• Replacement typically requires removing the control console or access panel and unplugging/replugging wire harnesses
• Handle the board by the edges and avoid touching components or connector pins

Size: 8-32 x 1/2 inch.

This replacement lever operates the overflow/level switch assembly to help the washer detect and respond to water level changes. It restores the mechanical action that tells the control when the tub is full. What it does:

• Moves the overflow/level switch mechanism so the machine can sense water level correctly
• Helps address overfilling, continuous filling, or erratic fill behavior caused by a worn or broken lever
• Restores reliable engagement between the float/actuator and the switch
• Works as the mechanical linkage for the overflow/level sensing assembly

• Disconnect power and turn off the water supply before beginning service.
• Access typically requires removing the cabinet or control console; keep fasteners organized.
• Install the lever so it aligns with the switch actuator and float linkage; verify smooth movement after assembly.

This caster support wheel helps restore smooth movement and stable support for the appliance's cabinet or drawer assembly. It replaces a worn or damaged wheel so the part rolls and aligns correctly. What it does:

• Replaces a worn or broken caster wheel that prevents smooth rolling
• Restores proper support and alignment for drawers or appliance base panels
• Reduces catching, scraping, or noisy movement caused by damaged rollers
• Helps maintain consistent front-to-back leveling when used with leveling hardware

• One caster support wheel

• Designed for basic drop-in replacement; position part where existing caster was mounted
• Turn off power and remove food/items or shelves from the cabinet/drawer area before working
• Use appropriate hand tools; avoid over-tightening fasteners which can bind the wheel

This is a genuine 4-24 x 3/8 screw used to fasten trim and components on compatible appliance assemblies. It provides a secure, vibration-resistant connection so panels and parts stay properly aligned during use. What it does:

• Secures panels, brackets, or components to the appliance frame
• Helps prevent rattling or loosening from normal vibration
• Works with threaded or self-tapping holes sized for a #4-24 fastener
• Common replacement for stripped, rusted, or missing mounting screws

• Use the matching screwdriver or nut driver to avoid stripping the head
• Tighten until snug; do not over-torque to prevent thread damage
• Replace any corroded or damaged screws in sets when multiple fasteners show wear
• Disconnect power and follow appliance safety guidance before servicing

This motor-pump is the dishwasher drain pump assembly that removes water from the tub so cycles can complete. Replacing a failed pump restores proper draining and helps prevent standing water and cycle errors. What it does:

• Spins the impeller to pump wastewater out of the dishwasher during drain cycles
• Stops leaks and prevents water from remaining in the tub when working correctly
• Commonly linked to symptoms such as no draining, water left in the tub, or a humming noise during drain
• Works as the integrated motor and pump — not a separate impeller-only part

• Disconnect power and shut off water supply before starting any repair
• Handle with care to avoid damaging the impeller, seals, or electrical connector
• May require removing access panels or the dishwasher kickplate; use appropriate tools

This dispenser cover (shield) replaces the plastic trim that surrounds a refrigerator's dispenser opening, restoring a clean finished look and helping direct water or ice into your cup. Fits where the dispenser meets the cabinet face. What it does:

• Covers and protects the dispenser opening, preventing chips and cosmetic damage
• Helps guide water and ice into cups for more accurate dispensing
• Hides internal dispenser components for a finished appearance
• Can reduce direct contact with moving dispenser parts

• One dispenser cover (shield)

• Remove power to the appliance before servicing to avoid electrical or injury risk
• Typically installs by snapping into place or fastening with a few screws; keep hardware if reusing
• Inspect surrounding trim for damage and replace any broken clips or screws for a secure fit

This dishwasher air gap prevents backflow from the sink into the dishwasher drain line, helping keep wastewater out of the appliance and reducing odors. It provides a simple, code-friendly way to vent the drain hose at the sink. What it does:

• Creates an air break in the dishwasher drain to prevent soiled water from flowing back into the machine
• Helps the dishwasher drain properly and reduces standing water in the tub or sink
• Reduces odors and contamination risk caused by backflow through the drain hose
• Works with most standard sink-mount dishwasher drain hose setups

• Designed for sink-mount installation; follow sink and dishwasher manufacturer instructions and local plumbing codes
• Use appropriate hose clamps and a secure hose connection to prevent leaks
• Inspect and clean the air gap periodically to remove debris

For spray arm seal use WP8268340.

This is a replacement sheet-metal screw used to secure panels and components on compatible Whirlpool appliances. It provides a reliable fasten point for reattaching trim, brackets, and access panels after service. What it does:

• Secures appliance panels, brackets, and smaller components to the cabinet or frame
• Helps restore original fit and finish after repairs or part replacement
• Prevents rattles or loose panels when properly installed
• Matches OEM thread size and head style for a correct fit

• Turn off and unplug the appliance before removing panels or installing hardware
• Use the correct driver bit to avoid stripping the screw head
• Tighten until snug; avoid over-torquing to prevent thread damage or warped panels

A flat washer used with fasteners on select top-load and front-load washer assemblies to distribute load and prevent loosening. Replaces worn or missing washers to help stabilize mounting points and reduce vibration where metal parts join. What it does:

• Provides a smooth bearing surface between a bolt or nut and the mating part
• Helps distribute clamping force to prevent damage to housings or panels
• Reduces loosening from vibration or thermal cycling
• Common fix when mounting hardware is loose, rattling, or causing leaks at joins

• Inspect mating bolt, nut, and surface for wear or damage before installing
• Use correct size and orientation; do not overtighten fasteners
• Disconnect power to the appliance and follow safety procedures when accessing internal parts
• Replace all related fasteners to ensure proper fit

This left-hand door hinge supports and pivots the door so it opens smoothly and closes tight. Replace a worn hinge to correct sagging, rubbing, or doors that won't seal—improving performance and preventing damage. What it does:

• Provides the pivot point for the door on the left side
• Maintains alignment so the door sits level and latches/seals properly
• Helps the door open and close smoothly without binding
• Common symptoms: door sags or rubs, won't close fully, uneven gaps, squeaking/grinding noises, poor seal

• One left-hand door hinge

• Disconnect power; also shut off gas and/or water before servicing
• Support or remove the door before unfastening the hinge; some hinges may be under spring tension—use caution
• Transfer original hardware/shims as needed and tighten fasteners securely
• Check door alignment and gasket contact after installation; open/close several times to ensure smooth operation

• "Left-hand" is determined when facing the front of the appliance.