Kenmore Dishwasher 665.17761891 (66517761891, 665 17761891) Parts

A small mounting clip that secures interior panels or trim pieces to the appliance, keeping parts aligned and preventing rattling or movement during operation. Simple replacement restores proper fit and reduces noise from loose components. What it does:

• Holds a panel, trim or small component in place on the cabinet or housing
• Keeps parts aligned so doors, panels or covers fit and operate smoothly
• Prevents rattling or vibration caused by loose or missing fasteners
• A worn or broken clip can allow gaps, movement, or noise during use

• Disconnect power (unplug or switch off breaker) before servicing
• Replacement typically requires only basic hand tools; keep track of any removed fasteners
• Inspect surrounding mounting points and adjacent clips for wear and replace as needed

This channel retainer secures the appliance's front/side panel to the cabinet so panels stay aligned and stable during use. It replaces a worn or broken retainer to reduce panel movement and rattling. What it does:

• Holds the panel channel in place to keep exterior panels aligned
• Prevents panel looseness, shifting, and vibration noise during operation
• Restores proper fit where a cracked or broken retainer allowed gaps
• Works as a direct-fit replacement for the OEM channel retainer

• One channel retainer as shown

• Inspect surrounding clips and screws; replace any damaged fasteners for best fit
• Use basic hand tools; avoid over-tightening fasteners which can crack plastic retainers
• Disconnect power (or unplug) the appliance before accessing panels

This replacement caster and socket assembly restores smooth rolling and stable support for the appliance cabinet. Use it to replace a worn or damaged wheel and mounting socket so the appliance moves easily and sits level. What it does:

• Provides a rolling wheel and mounting socket to support appliance movement and weight.
• Replaces cracked, seized, or worn casters that cause dragging, sticking, or uneven motion.
• Helps reduce noise and cabinet scuffs from a damaged or loose wheel.
• Restores proper alignment when the appliance tilts or does not roll smoothly.

• Disconnect power and water and move the appliance to a safe, stable work area before starting.
• Support the appliance to prevent tipping when removing/installing the caster.
• Remove any trim or mounting hardware covering the caster; match orientation and fasteners when installing the replacement.
• After installation, verify the appliance rolls smoothly and sits level; tighten fasteners as needed.

This replacement timer control knob lets you set and turn the appliance's timer with a clear grip and click-action feedback. It restores a worn or missing knob so you can reliably select time settings and operate the timer control. What it does:

• Provides a secure grip for turning the timer control and selecting time settings
• Replaces cracked, stripped, or missing timer knobs that are hard to turn
• Restores tactile click and positional indexing for accurate control
• Helps eliminate slipping or wandering of the timer pointer during use

• Install on the timer shaft by aligning the hub and pressing firmly until seated
• If knob is difficult to remove, use a flat tool gently; avoid damaging surrounding trim
• Disconnect power to the appliance before servicing timer components
• If the timer mechanism itself is damaged or nonfunctional, replace the complete timer assembly

This dishwasher air gap prevents backflow from the sink into the dishwasher drain line, helping keep wastewater out of the appliance and reducing odors. It provides a simple, code-friendly way to vent the drain hose at the sink. What it does:

• Creates an air break in the dishwasher drain to prevent soiled water from flowing back into the machine
• Helps the dishwasher drain properly and reduces standing water in the tub or sink
• Reduces odors and contamination risk caused by backflow through the drain hose
• Works with most standard sink-mount dishwasher drain hose setups

• Designed for sink-mount installation; follow sink and dishwasher manufacturer instructions and local plumbing codes
• Use appropriate hose clamps and a secure hose connection to prevent leaks
• Inspect and clean the air gap periodically to remove debris

This wheel leg is a replacement support used to stabilize and allow smooth movement of the appliance's lower assembly. It restores proper leveling and reduces wobble so the appliance sits securely and rolls or rests as designed. What it does

• Supports the appliance chassis at the lower corner and transfers load to the floor
• Helps maintain correct appliance height and leveling to reduce vibration and rocking
• Restores proper rolling or stationary support where a worn or broken leg caused instability
• Commonly replaced when the leg is cracked, stripped, missing, or no longer holds weight

• Verify appliance is unplugged and empty before accessing lower cabinet or base
• Support the appliance with a block or jack to prevent shifting while replacing the leg
• Remove any access panels or retaining hardware as needed; install the new leg in the original orientation
• Replace any fasteners that are damaged and test stability before returning the appliance to service

This is a replacement sheet-metal screw used to secure panels and components on compatible Whirlpool appliances. It provides a reliable fasten point for reattaching trim, brackets, and access panels after service. What it does:

• Secures appliance panels, brackets, and smaller components to the cabinet or frame
• Helps restore original fit and finish after repairs or part replacement
• Prevents rattles or loose panels when properly installed
• Matches OEM thread size and head style for a correct fit

• Turn off and unplug the appliance before removing panels or installing hardware
• Use the correct driver bit to avoid stripping the screw head
• Tighten until snug; avoid over-torquing to prevent thread damage or warped panels

These dishwasher cleaner tablets help dissolve and remove limescale, mineral deposits, and odor-causing residues from the tub and spray system. Use monthly or as needed to help maintain cleaning performance and a fresh-smelling interior.

• Breaks down hard-water scale and detergent film that can accumulate inside the dishwasher
• Helps reduce lingering odors caused by trapped residues
• Supports proper spray performance by cleaning internal surfaces and passages
• Helpful when you notice white film, cloudy glassware, or persistent smells

• Run with the dishwasher empty; follow the package directions for tablet placement and cycle selection
• Do not add other cleaners or detergent during the cycle
• Keep out of reach of children; avoid contact with eyes; wash hands after handling
• For heavy buildup, repeat use per label instructions

The Thermostat Clip is an OEM part for Whirlpool dishwashers. It plays an important supporting role by securely fastening the thermostat sensor inside the wash chamber. 

Symptoms of a faulty Thermostat Clip can include:

• Fluctuating or inconsistent water temperatures between cycles 
• Inability to properly detect temperature for desired heat levels
• Longer cycle times needed for reaching required temperatures
• Strange sounds or condensation around thermostat connection

Causes could arise from typical wear and tear stresses weakening plastic retaining clips. Exposure to harsh detergents may also erode clip material integrity over time.

This OEM replacement part is compatible with KitchenAid, Jenn-Air, Kenmore, and select Hotpoint and Roper dishwasher models as well.