Kenmore Microwave 721.80039700 (72180039700, 721 80039700) Parts

This door latch assembly for a microwave engages the door hooks and actuates the interlock switches so the unit recognizes a closed door, restoring proper latching and helping ensure the oven only operates when securely shut.

• Engages the door hooks to trigger the interlock switches and signal "door closed"
• Can help resolve no-start or "Door/Open-Close" indications with the door shut
• Addresses a door that won't latch, feels loose, or shows cracked/worn latch parts
• Built to mount in the original location and interface with existing door switches

• Disconnect power before service; microwaves contain high-voltage components that can retain a dangerous charge
• Access typically requires removing the control panel to reach the latch/interlock bracket
• Note switch orientation and spring positions; transfer any reusable hardware from the old assembly
• After installation, verify firm door engagement and proper interlock switch actuation before restoring power

This replacement door glass restores a clear viewing window and the protective barrier on your microwave door. Replace it when the original panel is cracked, shattered, or heavily scratched to keep the door secure and safe to use.

• Provides the see-through window and protective barrier within the microwave door
• Helps maintain proper door rigidity and alignment when intact
• Replace if the glass is cracked, chipped, shattered, loose, or badly scratched
• Reduced visibility, rattling, or visible damage are common symptoms of failure

• Unplug the microwave before servicing; microwaves can retain high voltage—use caution and do not open the cabinet
• Support the door; removal from the hinges may be required per your model's diagram
• Handle glass with cut-resistant gloves; edges can be sharp
• Transfer any reusable trim/clips as directed and verify the door latches and closes properly after installation

This truss head tapping screw secures panels, brackets, and covers in your appliance. Replacing a missing or damaged fastener restores a snug fit, reduces vibration, and helps keep components properly aligned for reliable performance.

• Provides low-profile holding power; wide truss head helps secure thin panels and trim
• Replaces lost, stripped, or corroded screws at the original mounting points
• Helps eliminate rattling, vibration, or loose handles/covers
• Addresses situations where a screw will not tighten or backs out during use

• Disconnect power; shut off water/gas if applicable before servicing
• Align parts and hand-start threads to avoid cross-threading
• Tighten until snug; do not overtighten to prevent stripping
• If the receiving hole is damaged, for repair before installing the new screw

This microwave thermostat is the safety control that monitors temperature and opens the circuit if overheating is detected, protecting internal components. Replace it if your oven is dead, loses heat, or shuts off mid-cycle due to a failed thermostat. What it does:

• Monitors temperature and interrupts power when overheating occurs to help prevent damage
• Helps protect internal components and wiring from excessive heat
• Failure can cause: no power, shuts off during or shortly after starting, or runs but does not heat
• Replacing a failed thermostat helps restore normal operation and safety protections

• 1 thermostat

• Unplug the appliance; microwaves contain high-voltage components that can retain a lethal charge even when unplugged
• Remove the outer cover to access the thermostat; location varies by model
• Move wires one at a time to the new thermostat and mount it firmly against the mating surface for proper heat sensing
• Reassemble, restore power, and test operation

This canopy resistor regulates current to a range-hood or canopy fan circuit to help the blower run at the correct speeds. Replacing a failing resistor can restore proper fan speed control and stop intermittent operation. What it does:

• Controls electrical resistance in the canopy/blower circuit to help regulate fan speeds.
• Helps prevent the motor from running only on a single speed or from failing to start at selected speeds.
• Can cause symptoms such as inconsistent fan speeds, no response from speed controls, or occasional fan cutoff.
• Works with the hood's wiring and control switch to deliver the correct voltage to the fan motor.

• Disconnect power to the appliance before accessing the canopy or electrical connections.
• Inspect wiring and connectors for heat damage or corrosion; replace harness or terminals if damaged.

This factory fastener secures appliance panels and components. Use it to replace a missing, stripped, or corroded screw so brackets, covers, and assemblies stay tight and properly aligned, helping reduce vibration and rattling.

• Secures panels, brackets, and internal components in their proper positions
• Replaces missing, worn, or cross-threaded hardware
• Helps eliminate vibration and rattling from loose parts
• Supports proper alignment of covers and assemblies

• Disconnect power to the appliance before servicing; allow any moving parts to stop
• Match this screw to the location shown in your model's parts diagram
• Start threads by hand to avoid cross-threading, then tighten snugly with the correct driver
• Do not overtighten to prevent stripping threads or cracking plastic bosses

This is a truss-head tapping screw used to secure trim, panels, and small assemblies on compatible LG appliances. It provides a low-profile, wide-bearing head that helps hold parts flush and resist pull-through. What it does:

• Fastens plastic and sheet-metal components where a self-tapping thread is needed
• Truss head spreads load to prevent damage to soft or thin materials
• Helps secure control panels, brackets, or trim pieces that require a low-profile head
• Common replacement when original mounting screws are missing, stripped, or corroded

• One truss-head tapping screw

• Use the correct screwdriver bit and moderate torque to avoid stripping the screw or workpiece
• Start threading straight and let the screw form threads without forcing at an angle
• Disconnect power and follow appliance-specific service safety procedures before working internally
• Replace any damaged mating threads or clips for a secure fit

This is a replacement screw used to secure appliance components and panels. It restores proper fastening where a stripped, missing, or damaged screw causes loose parts or rattling. What it does:

• Fastens panels, trim, or internal components to maintain structural fit
• Helps stop vibration-related noise from loose assemblies
• Replaces missing or corroded screws that prevent proper closures
• Restores secure mounting after repairs or disassembly

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug—do not over-torque to prevent thread damage
• Keep small parts away from children and pets
• Disconnect power or water before accessing internal parts

Inner plastic door film covers the holes in the inner door frame.

A high-voltage capacitor for the appliance's high-voltage circuit that stores and releases electrical energy to support proper heating operation. Replacing a failing capacitor can restore consistent heating and prevent related electrical faults. What it does:

• Stores and delivers high-voltage energy used by the magnetron/ high-voltage assembly to generate heat.
• Failure may cause no-heat or weak-heat conditions in the oven.
• Faulty capacitors can contribute to arcing, loud humming, or blown high-voltage fuses.
• Works as part of the HV circuit; not a user-serviceable low-voltage control.

• High-voltage components can hold a dangerous charge—disconnect power and discharge the capacitor before servicing.
• Use insulated tools and avoid touching terminals; verify proper operation with appropriate test equipment.

This is a motor start/run capacitor that helps the appliance's motor start and run smoothly by supplying a brief boost of electrical energy. Replacing a failing capacitor restores reliable motor startup and operation. What it does:

• Provides the brief electrical surge needed to start and keep the motor running
• Commonly linked to motors that hum, fail to start, or run intermittently
• Helps prevent overheating from repeated start attempts when functioning properly
• Works with the appliance's start circuitry to ensure consistent performance

• Disconnect power to the appliance before accessing electrical components
• Discharge the capacitor and use insulated tools
• Observe polarity/terminal layout and secure connections to factory specifications
• Dispose of the old capacitor according to local electronic-waste regulations

A Tap-Tite binding-head screw used to fasten appliance panels and components where a self-tapping metal thread is required. Replaces missing or damaged fasteners to restore secure assembly and reduce vibration or rattling. What it does:

• Creates its own mating thread in thin sheet metal for a secure hold without a nut.
• Holds panels, brackets, and trim in place to prevent looseness or movement.
• Commonly used where stripped, missing, or broken screws cause rattling, misalignment, or parts that won't stay attached.
• Compatible with standard screwdrivers or nut drivers sized to the binding-head.

• Disconnect power and unplug the appliance before working on it.
• Use the correct driver bit to avoid cam-out or head damage.
• Start straight and apply steady pressure; avoid overtightening to prevent stripping the formed threads.
• If the original hole is badly damaged, assess for repair or use of a larger fastener as needed.

This mechanical charcoal refrigerator filter helps reduce food and fridge odors for fresher-smelling compartments. It's a direct-fit replacement that restores odor-absorbing capability so your fridge interior smells cleaner. What it does

• Adsorbs and traps common food and household odors to reduce smells in the fridge
• Helps prevent odor transfer between compartments and stored foods
• Restores the intended odor-control function when the original filter is spent or clogged
• Works as a simple replaceable cartridge in compatible LG refrigerator filter housings

• One mechanical charcoal refrigerator filter cartridge

• High-level replacement: remove the old filter cartridge and snap or twist the new cartridge into the filter housing per the refrigerator manual
• Follow the refrigerator manufacturer's instructions for alignment and secure seating to avoid leaks or loss of function
• Disconnect power or follow any appliance-specific safety steps recommended by the manufacturer before servicing
• Dispose of the used filter per local regulations for household waste

This replacement lamp assembly restores interior illumination so you can see the appliance cavity clearly and safely. It fits the original mounting and electrical connections for a direct swap. What it does

• Replaces a burned-out, flickering, or dim interior lamp so you can inspect food and parts easily
• Provides the correct shape and connector to match the appliance's original lamp location and mounting
• Helps eliminate intermittent lighting caused by a damaged lamp or failed lamp connection
• Restores normal light output for safe loading and unloading

• Disconnect power to the appliance before starting any repair
• Allow the appliance and old lamp to cool completely before handling
• Handle the lamp by its base or use gloves to avoid oil contamination on the bulb
• Follow the appliance's service manual or OEM diagram for correct removal and installation