Kenmore Range 790.31053000 (79031053000, 790 31053000) Parts

This is a replacement glass door assembly made by Frigidaire. It is made of tempered glass and allows the user to see into the oven and observe food as it cooks. It also prevents heat from escaping.Glass oven doors can be damaged by contact with cold liquids that cause the glass to contract rapidly. If the glass is cracked or broken, the door will need to be replaced. To replace the oven door, locate the screws under the door lip. Remove the bolts holding the handle to the front, and the door should lift away. Reverse these steps to install the new door. The door is quite heavy and may require two people to safely uninstall/install.This is an OEM part. It is sold individually and is compatible with Kenmore and Frigidaire ovens.

A genuine replacement refrigerator door handle that restores a secure grip and reliable opening on compatible units. Designed to match the original fit and finish so you can use the door normally again. What it does:

• Replaces a broken, cracked or missing refrigerator door handle
• Provides a solid grip for opening and closing the door smoothly
• Restores proper alignment and appearance of the door front
• Helps prevent further damage from improvised grips or taped-on handles

• One replacement refrigerator door handle

• Basic hand tools typically required; follow the OEM instructions for fastener locations
• Work carefully to avoid scratching the door finish and to retain any mounting clips or screws
• If the handle is near electrical components, unplug the appliance or disconnect power before starting

This is a replacement screw used to secure appliance panels and components. It restores proper fastening so panels, trim, or assemblies stay tight and reduce vibration or rattling. What it does

• Fastens panels, brackets, or trim to the appliance chassis
• Helps stop loose or vibrating panels and trim pieces
• Restores proper alignment where a missing or stripped screw causes gaps or movement
• Use when the original screw is missing, damaged, or corroded

• One replacement screw as shown

• Disconnect power to the appliance before starting any repair
• Use the correct screwdriver or bit to avoid stripping the screw head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Keep removed screws in a safe place; this screw matches the original before installation

This outer housing cover restores the refrigerator's finished appearance and protects internal components from dirt and accidental contact. It provides a clean trim surface and helps maintain proper airflow around covered areas. What it does

• Covers and protects internal components and wiring from spills, dust, and impact.
• Restores a secure, finished appearance where a cracked or missing cover leaves exposed parts.
• Helps eliminate rattles or gaps caused by broken or loose trim pieces.
• Prevents accidental contact with moving parts or electrical connections behind the cover.

• Disconnect power to the appliance before starting any work.
• Most installs require removing adjacent trim or fasteners; keep screws and clips for reassembly.
• Handle plastic clips and tabs carefully—damaged clips may require replacement.
• If alignment is difficult, check for obstructing components or bent mounting tabs before forcing the part into place.

This wiring harness routes power and signals between a refrigerator's control board and major components, restoring reliable electrical connections for proper operation. Use it when connectors are damaged or wiring is worn. What it does:

• Carries power and control signals between the main control and components
• Replaces burned, frayed, or broken wire runs that cause intermittent or no component operation
• Restores secure connector interfaces to fix flickering lights, non-running fans, or no cooling symptoms
• Preserves correct wiring routing to prevent shorts and maintain safe operation

• One wiring harness assembly as shown

• Always disconnect power to the appliance before starting work
• Handle connectors gently; match keyed plugs and secure all mating clips
• Route harness along original paths and secure with existing clips or ties to avoid pinching
• Replace any damaged connectors or terminals to ensure a reliable connection

This front console control panel replaces a worn or damaged oven/range control surface and restores access to your unit's buttons and display for normal operation. It provides the visible interface where settings are selected and displayed. What it does:

• Replaces the exterior control surface used to select cook modes, temperatures, and timers
• Restores tactile button access and the area around the display when the original panel is cracked, faded, or broken
• Commonly used when buttons stick, the panel is cosmetically damaged, or the control surface no longer secures properly
• Does not include electronic control boards or internal components unless specified

• High-level task: remove screws and trim pieces, disconnect any ribbon cables or harnesses, and secure the new panel in place
• Disconnect power at the breaker before servicing to avoid electrical shock
• Handle ribbon cables and connectors gently; do not bend pins or force connectors

This support bracket secures and stabilizes appliance components, restoring proper alignment and stopping movement. It's a simple replacement that helps reduce rattling and prevents panels or assemblies from shifting during use. What it does:

• Provides a rigid mounting point to hold panels, trim, or internal assemblies in place
• Restores proper alignment when a worn or broken bracket causes gaps or looseness
• Reduces vibration and rattling caused by a damaged or missing support
• Keeps connected parts from shifting, which can prevent further wear or damage

• Disconnect power to the appliance before beginning any repair
• Verify the bracket orientation and fit against the mating surface before fastening
• Use the factory screw locations and hardware; tighten screws securely but avoid over-torquing

This mounting bracket secures internal panels or components to the appliance frame, restoring stable support and alignment for proper operation. Use when a bracket is bent, broken or missing to reduce rattling and keep parts positioned correctly. What it does:

• Anchors panels or components to the cabinet/frame to prevent movement and vibration
• Restores proper alignment of doors, panels or internal assemblies
• Stops rattling or buzzing caused by loose or damaged support hardware
• Helps maintain safe clearance between parts and wiring or moving components

• Disconnect power to the appliance before starting any repair
• Basic hand tools typically required; follow OEM instructions for correct fastener locations
• Inspect adjacent fasteners and mounting surfaces; replace any damaged screws or clips
• If bracket is corroded or severely deformed, replace rather than re-bend to ensure proper fit