Kenmore Range 790.46599500 (79046599500, 790 46599500) Parts

This genuine OEM part is a oven door glass. The glass oven door assembly is the main oven door used to gain access to the interior of the oven. Over time a glass door assembly can become damaged due to excessive wear and tear. If the door is no longer shutting properly it might be time to replace it. Luckily replacing a glass door assembly is a fairly simple repair.To replace the door assembly, begin by unpluggin the oven. Once unplugged, open the damaged door assembly and locate the hinge brackets on the side of the door. Remove the screws from the mounting brackets. Once remove, gently lift the door off the hinges. Set to the side and place the new door directly on the hinges. Refasten the screws that secure the door, and close the new oven door. Make sure that it opens and shuts smoothly.This replacement part is sold individually and is compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse brand ovens.

This replacement drawer body restores a smooth-sliding storage bin in your appliance. Integrated rollers let the drawer glide on its tracks, keeping items organized and easy to access when the original is cracked, warped, or difficult to open.

• Forms the storage bin and supports items within the compartment
• Built-in rollers enable smooth travel along the drawer rails/tracks
• Helps resolve sticking, popping off track, rough movement, or broken tabs
• Restores proper fit and slide action for everyday use

• Empty and remove the damaged drawer; transfer any reusable front trim or inserts from the old drawer if needed
• Clean and inspect the rails/tracks; align the rollers with the track openings and slide in level until fully seated
• Do not force the drawer—re-align if resistance is felt to avoid damaging tabs or rails
• Avoid lubricants; wipe tracks and rollers with mild soap and water only

This handle mounting screw is an authentic OEM replacement part sourced directly from the manufacturer for use with oven handles. The oven handle attaches to the oven door with two of these screws. If the washer that goes with the screw is loose or missing, the screw will become loose, and the handle may break away from the door. If this occurs, the door will be difficult to open when not in use and nearly impossible to open when hot. If the mounting screw is loose or missing, the screw should be replaced immediately. Note that the washer needed for the screw is not included and should be purchased separately.Make sure the oven is not hot before replacing the door handle mounting screw. To start, disconnect the power from the oven. Remove the screw and washer from the handle if it is loose and install a new handle mounting screw with a new washer. Tighten the screw until it is flush with the door. Repeat for the remaining screw if necessary.This handle mounting screw is a heavy-duty black metal screw that is sold individually. It is designed for use on ovens manufactured by Frigidaire.

This high-temperature insulation is used in the oven assembly to contain heat and protect nearby components and cabinetry. Replacing damaged insulation helps the appliance maintain set temperatures and keeps exterior surfaces from getting excessively hot. What it does:

• Helps retain heat for stable baking and roasting temperatures
• Reduces heat transfer to the appliance frame and adjacent cabinets
• Replaces insulation that is torn, charred, or saturated with spills/grease

• One insulation piece

• Disconnect power; for gas models, also shut off the gas supply
• Remove the range or wall oven and access the oven body
• Wear gloves, eye protection, long sleeves, and a dust mask; fibers can irritate skin and lungs
• Reinstall in the same orientation/routing as the original; do not compress insulation or block vents

This replacement refrigerator door handle restores a secure, easy-to-grip pull for opening and closing the fridge. It matches the original mounting points for a clean, factory-fit appearance. What it does

• Replaces a cracked, loose, or broken refrigerator door handle so the door can be opened and closed safely.
• Provides a solid grip to help prevent slips and accidental drops.
• Restores proper clearance and alignment at the door edge for smooth operation.
• Helps maintain the appliance's original look and usability.

• One replacement refrigerator door handle.

• Installation requires removing the old handle and fastening the new handle to the existing mounting points; keep mounting screws and any trim pieces from the original assembly.
• Use basic hand tools; avoid over-tightening fasteners to prevent cracking the handle.
• Disconnect power only if instructed by the appliance manual for your specific model (most handle replacements do not require powering down).
• If the handle attaches under a trim or gasket, take care to reseat trim evenly to maintain door seal integrity.

This door push-button light switch controls the interior lamp by turning it on when the refrigerator door opens and off when the door closes. It replaces a worn or failed push-button actuator to restore reliable light operation. What it does:

• Completes the circuit to the interior light when the door opens and breaks the circuit when closed
• Commonly causes no interior light, intermittent lighting, or lights that stay on
• Fits in the refrigerator door frame and interfaces with the existing wiring harness
• Simple, single-function electromechanical switch—no electronics to program

• One door push-button light switch

• Disconnect power to the appliance before servicing to avoid shock
• Remove the door trim or bezel as needed to access the switch (requires basic hand tools)
• Handle the switch and wiring gently; do not force connectors or overtighten fasteners

This element hanger support secures a cooktop surface heating element to the range and keeps the element aligned for reliable contact and stable cooking. Replaces a worn or bent bracket to restore proper element positioning. What it does:

• Holds the surface heating element in the correct position under the cooktop
• Stabilizes the element to maintain solid electrical contact and even heating
• Helps prevent element wobble, arcing, or intermittent power to the burner
• Fits where the element connects to the terminal/anchor point on the cooktop

• 1 element hanger support bracket

• Disconnect power to the appliance before attempting any service
• Remove the cooktop or element as required to access the hanger; follow OEM disassembly steps
• Inspect element terminals and surrounding parts for damage while replacing the bracket

This shoulder screw secures moving or fixed appliance components by providing a built-in spacer and pivot point for proper alignment and smooth operation. It restores correct fit where a worn or missing shoulder fastener causes play. What it does:

• Provides a precision spacer and pivot for hinges, drawers, or linkage assemblies
• Holds components at the correct distance to prevent rubbing and binding
• Helps stop wobble, misalignment, rattling, or uneven movement when the original shoulder screw is worn or missing
• Works where a headed screw with an integrated shoulder is required for smooth rotation or exact spacing

• One shoulder screw

• Disconnect power and remove the appliance panel or access covers before replacing hardware
• Handle small parts carefully to avoid dropping them into assemblies; magnetic pickup tool can help
• Install in the original location and tighten securely but avoid overtightening; do not modify the shoulder or thread
• If the screw secures a load-bearing hinge or mechanism, verify alignment and operation after installation