Kenmore Range 790.60071790 (79060071790, 790 60071790) Parts

Replacement handle end cap that restores a finished appearance and secures the outer end of an appliance handle. Ideal for replacing cracked, chipped, or missing end caps that affect grip or the handle's look. What it does:

• Covers and protects the exposed outer end of a handle for a clean, finished appearance
• Restores proper fit and helps prevent further damage where the handle meets the door or drawer
• Addresses symptoms like a loose, chipped, cracked, or missing end cap that affects appearance or feel

• Installation method varies by model; part may snap into place or be secured with fasteners—refer to your model's service guide
• If working on a powered appliance, disconnect power before servicing
• Use appropriate hand tools and avoid prying on surrounding trim to prevent damage

This body-side spacer installs on the cabinet side of the door or lid hardware. It sets the correct stand-off and alignment so the handle or latch feels solid and sits flush for a clean, secure fit. What it does:

• Positions and supports door/lid hardware on the cabinet/body side
• Maintains proper spacing to help prevent rubbing or scuffing of the panel
• Helps keep the handle or latch tight and aligned
• Common symptoms: loose or wobbly handle/latch, uneven alignment, visible gap or scuff marks at the mounting point

• Includes 1 body-side spacer

• Disconnect power to the appliance before servicing
• Support the handle/latch, remove the cabinet-side mounting screws, place the spacer, realign hardware, and reinstall screws snugly
• Reuse the original fasteners; avoid overtightening to prevent cracking the spacer or stripping threads
• Check door operation and alignment before finishing

Original Frigidaire Part.

This hex flange nut secures components where a broader bearing surface is needed to resist loosening and distribute load. It fits 10-32 threaded studs and is used on fastened assemblies in appliances. What it does:

• Provides a secure threaded connection for 10-32 screws and studs
• Flange spreads clamping force to reduce panel or bracket damage
• Hex shape allows tightening with a wrench for a reliable hold
• Commonly replaces worn or missing nuts that cause loose panels or rattling

• One hex flange nut

• Use the correct 10-32 screw or stud and hand-start threads to avoid cross-threading
• Tighten with an appropriately sized wrench; do not overtighten to prevent thread or part damage
• Disconnect power and follow appliance safety instructions before servicing
• Replace only like-for-like; confirm size and thread match your application

This oven back insulation panel fits behind the oven cavity to help contain heat and protect rear components. It replaces missing or damaged insulation to help restore normal oven heating behavior and reduce heat transfer to surrounding areas. What it does:

• Limits heat loss from the rear of the oven cavity to help maintain cooking temperature
• Helps reduce excessive heat transfer to rear components and cabinetry
• Use when insulation is torn, compressed, burned, or when the oven takes noticeably longer to preheat
• Helps prevent heat-related damage to wiring, electronics, and nearby parts

• Disconnect power to the appliance before starting any repair
• Access may require pulling the range/oven away from the wall and removing a rear access panel
• Wear gloves and a dust mask when handling old insulation; avoid compressing or tearing the replacement
• Follow OEM instructions for securing insulation with the original clips/adhesive or fasteners

Oven wrapper insulation that surrounds the oven cavity to retain heat, protect outer panels, and improve temperature stability—helping reduce exterior heat and support more consistent cooking results. What it does:

• Wraps the oven cavity to reduce heat transfer to the cabinet and outer panels.
• Helps maintain internal oven temperatures for more even baking and cooking.
• Damaged or missing insulation can allow outer surfaces to run hot, cause longer preheat times, or contribute to uneven cooking.
• Reduces the risk of heat-related damage to surrounding cabinetry and components.

• Disconnect power and allow the appliance to cool completely before servicing.
• Handle insulation with care; avoid compressing or tearing the material during installation.
• Reinstall using original mounting clips or hardware; verify proper fit around the oven cavity before replacing panels.

Size: 8-18ab x 0.5 inch.

This small push-in plug button caps the opening in an oven bottom to keep the cavity clean and finished-looking. It prevents food and debris from falling into the oven base and restores a secure, even interior surface. What it does:

• Covers and seals the hole in the oven bottom to prevent debris buildup
• Helps maintain a finished appearance and reduces hotspots around openings
• Stops loose items from dropping into the oven base and interfering with components
• Simple, low-profile cap designed for a snug, friction-fit installation

• Turn the oven off and allow it to cool completely before installing
• Press the plug button firmly into the opening until it seats flush
• Use a non-marring tool if needed to avoid scratching the oven surface
• Replace with the correct OEM part if the plug does not fit securely or is damaged