Kenmore Range 790.70112703 (79070112703, 790 70112703) Parts

Igniter and orifice assembly includes: Igniter, orifice assembly and gas tube.

This oven back insulation panel fits behind the oven cavity to help contain heat and protect rear components. It replaces missing or damaged insulation to help restore normal oven heating behavior and reduce heat transfer to surrounding areas. What it does:

• Limits heat loss from the rear of the oven cavity to help maintain cooking temperature
• Helps reduce excessive heat transfer to rear components and cabinetry
• Use when insulation is torn, compressed, burned, or when the oven takes noticeably longer to preheat
• Helps prevent heat-related damage to wiring, electronics, and nearby parts

• Disconnect power to the appliance before starting any repair
• Access may require pulling the range/oven away from the wall and removing a rear access panel
• Wear gloves and a dust mask when handling old insulation; avoid compressing or tearing the replacement
• Follow OEM instructions for securing insulation with the original clips/adhesive or fasteners

Size: 8-18ab x 0.5 inch.

This metal ignitor shield protects the oven or range ignitor assembly from direct heat and debris, helping maintain reliable ignition and prolong the ignitor's life. It's a simple replacement that restores proper burner protection. What it does:

• Shields the ignitor from spills, drips, and direct flame exposure
• Helps ensure consistent ignition by protecting the ignitor element
• Common symptom: oven or range taking longer to light or erratic ignition
• Common symptom: visible damage or corrosion to the existing shield

• Disconnect electrical power and shut off gas supply before starting work
• Handle parts carefully; avoid contact with the ignitor surface to prevent damage
• Verify correct orientation and secure mounting per the appliance's service instructions

This manifold pipe routes gas from the valve assembly to the oven or cooktop burners, restoring proper fuel distribution for reliable ignition and flame performance. Designed as a direct replacement to maintain safe burner operation. What it does:

• Distributes gas evenly from the main gas valve to individual burners
• Enables burners to light and maintain steady flames
• Helps eliminate weak or no-flame symptoms tied to a damaged or clogged manifold
• Works with the range/oven gas system components for proper combustion

• One manifold pipe

• Turn off the gas supply and power to the appliance before service
• Inspect fittings and replace any damaged gaskets or seals; use pipe sealant appropriate for gas connections if required
• After installation, check all connections for leaks with a gas leak detector or soapy water; do not use an open flame

This service tech sheet is the factory diagnostic guide that helps troubleshoot and verify appliance components. It provides clear reference information technicians use to identify wiring, error codes, and common diagnostic steps for repairs. What it does:

• Shows factory wiring diagrams and component locations for quick reference during diagnosis
• Lists common error codes and troubleshooting checks to narrow down failures
• Provides step-by-step diagnostic guidance technicians use to confirm faulty parts
• Helps reduce guesswork when an appliance won't power on, shows error codes, or has intermittent operation

• This is a reference document, not a wearable or electrical component; store it in a dry, accessible place near the appliance
• Always disconnect power to the appliance before performing any testing or repairs suggested by the sheet
• Follow all safety guidance and manufacturer procedures shown on the sheet; use protective equipment as required
• Replace the sheet if damaged or illegible to ensure accurate diagnostics

This support bracket secures and stabilizes internal appliance components to keep assemblies aligned and reduce vibration. Simple replacement restores proper mounting where worn or damaged brackets allow movement. What it does:

• Provides a secure mounting point for internal parts and assemblies
• Keeps panels and components aligned to prevent rubbing or misalignment
• Reduces rattling or vibration caused by a broken or loose bracket
• Commonly replaced when brackets are bent, cracked, or missing fasteners

• Disconnect power and water (if applicable) before starting any repair.
• Keep track of all fasteners and mounting hardware; some original screws may be reused.
• Use basic hand tools; avoid overtightening to prevent damage to bracket or mounting points.