Kenmore Range 790.77512806 (79077512806, 790 77512806) Parts

This replacement power cord restores electrical connection to the appliance so it can receive mains power safely. Use it when the original cord is frayed, damaged, or no longer providing a reliable connection. What it does:

• Replaces a damaged or worn appliance power cord to restore reliable power
• Resolves intermittent power, sparking at the plug, or visible cord damage
• Provides the necessary insulated conductors for safe appliance operation
• Works as a direct cord-replacement when the original cord is defective

• Always disconnect power at the breaker or unplug the appliance before installing
• Route the cord and secure strain relief per the appliance's original routing to prevent pinching
• Ensure the cord's connector and grounding match the appliance's inlet before connecting

Note: ONE screw only, order as needed.

This oven door latch assembly locks the door during self-clean and reports lock status to the control. Restores proper door locking and unlocking so bake and clean cycles can run safely and without interruptions. What it does:

• Secures the oven door during self-clean and when commanded by the control
• Provides locked/unlocked position feedback to the electronic control
• Helps resolve issues such as a door that won't lock or unlock
• Can address self-clean cycles that won't start or complete and lock-related error messages

• 1 latch assembly

• Disconnect power at the breaker and allow the oven to cool completely
• Access varies by model; you may need to pull the unit and remove the rear or top/control panel
• Photograph wire connections and linkage before removal; transfer any mounting hardware from the original
• After installation, test the lock operation before final reassembly

This door trim kit restores the finished edge around the appliance door, covering raw edges and fasteners. Replace worn or missing trim to refresh the look and help keep the outer door panel properly seated. What it does:

• Finishes the perimeter of the door and conceals mounting hardware
• Helps retain and align the outer door panel or glass
• Replaces cracked, warped, loose, or missing trim pieces
• Typical symptoms include gaps around the door, loose or rattling edges, or cosmetic damage

• One door trim kit

• Disconnect power to the appliance before servicing
• Wear cut-resistant gloves; door edges and trim can be sharp
• Support or remove the door as required by your model; note screw locations and lengths
• Transfer any clips/screws from the original trim and check door alignment and operation after installation

For 12k burner.

This fan motor drives your oven's convection fan, circulating hot air for even, reliable cooking performance. Replacing a weak or noisy motor restores proper airflow to reduce hot spots and improve convection baking and roasting results. What it does:

• Powers the rear convection fan to move air across the oven cavity
• Promotes more uniform temperatures on multiple racks during convection cycles
• Helps the oven maintain stable heat during use
• Common symptoms: fan won't spin, intermittent or slow rotation, loud humming/scraping from the rear, uneven results in convection mode

• 1 fan motor

• Disconnect power to the range or wall oven before servicing
• Access may require removing the rear panel or the oven's rear cover; note wire locations for reassembly
• Transfer the original fan blade and mounting hardware to the new motor; handle sharp edges and avoid bending the blade
• Spin the blade by hand to ensure free movement before restoring power

This oven light lens retainer secures the glass light cover to the oven cavity so the bulb area stays protected during cooking. Replacing a damaged or missing retainer keeps the lens firmly in place and prevents nuisance loosening.

• Holds the glass light lens securely inside the oven cavity
• Helps shield the bulb area from splatters and debris
• Direct replacement for a bent, warped, or missing retainer ring
• Common symptoms: lens won't stay in, cover rattles, or difficulty securing the lens after service

• Disconnect power at the breaker and allow the oven to cool completely
• Remove oven racks for easier access to the light cover area
• Support the glass lens while positioning the retainer to avoid drops or chipping
• Secure the retainer per your model's design; do not overtighten

This convection fan element mounts on the oven's rear wall around the blower. It supplies supplemental electric heat so the fan can circulate hot air evenly during convection modes for more consistent baking and roasting.

• Provides heat directly around the convection fan to help maintain even temperature during convection cycles
• Failure can cause poor browning, uneven results on multiple racks, or convection modes that run without proper heating
• May show visible breaks, blistering, or burnt spots; an open element will fail a continuity check
• If standard bake heats normally but convection bake does not, this element may be at fault

• Disconnect power at the breaker and allow the oven to cool completely before servicing
• Remove oven racks and the rear interior panel to access the element surrounding the fan
• Note wire positions; transfer any spacers or mounting hardware from the original element as needed
• Secure the element without bending it and confirm the fan spins freely with proper clearance

This small replacement spacer positions and secures appliance components to maintain correct alignment and fit. Installing the spacer restores proper panel spacing and reduces vibration where a worn or missing spacer causes looseness or rubbing. What it does:

• Maintains the correct gap between panels, trim, or assemblies to ensure parts fit flush
• Keeps components aligned to prevent rubbing, binding, or uneven wear
• Helps reduce vibration and rattling caused by a missing or damaged spacer
• Preserves original part spacing for reliable operation of the surrounding components

• Disconnect power to the appliance before any service to avoid shock or injury
• Remove any trim or fasteners that block access; keep track of screws and small parts
• Match the new spacer's orientation to the original; do not force parts into place

Replacement screw that secures panels, trim and internal components in compatible appliances. Restores proper fit and helps reduce rattling or loose parts when the original fastener is missing, worn, or damaged. What it does:

• Fastens panels, brackets, trim pieces and small component assemblies to the appliance frame
• Helps eliminate noise and vibration caused by loose or missing fasteners
• Replaces stripped, corroded or missing screws to restore secure mounting
• Matches OEM fit when the identical screw is required for proper alignment

• Disconnect power to the appliance before starting any repair
• Use the correct driver size to avoid cam-out or damage to the screw head
• Do not overtighten; overtightening can strip threads or crack plastic parts

This wiring harness connects the appliance's electrical components to restore reliable power and signal routing. It replaces a damaged or worn harness to help resolve power loss and intermittent electrical issues. What it does:

• Transfers power and control signals between components so controls and motors can operate
• Replaces frayed, burned, or broken wiring that can cause intermittent operation
• Helps stop failures that lead to no-start or loss of specific functions
• Restores secure connector fit to reduce arcing or poor connections

• Always disconnect power before servicing the appliance
• Match connectors and wire routing to the original harness; avoid stretching or pinching wires
• Secure fasteners and strain reliefs; verify all connections are fully seated
• If you find heat or burn damage at terminals, inspect adjacent components for root cause

This electrical receptacle is the small connector that secures a wiring plug to an appliance component, restoring a reliable electrical connection and preventing intermittent operation or arcing. What it does:

• Provides a secure plug-in connection between a wire harness and a component
• Restores power to a component when the original connector is cracked, melted, or corroded
• Helps prevent loose connections that can cause intermittent operation or sparks
• Fits the OEM-style wiring configuration for a direct replacement

• Disconnect power to the appliance before starting any repair
• Remove the damaged connector and match the replacement to the harness before installing
• Use basic hand tools; avoid forcing terminals to prevent damage

This is a replacement mounting screw used to secure panels and components in compatible Frigidaire appliances. It restores proper fit and helps prevent rattles, loose panels, and parts that shift during operation. What it does:

• Fastens trim, panels, brackets, or controls to the appliance frame
• Restores secure attachment to reduce vibration, noise, and movement
• Replaces stripped, missing, or corroded screws that prevent proper assembly
• Works wherever the OEM screw with this part number is specified

• Disconnect power to the appliance before beginning any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug—do not overtighten to avoid stripping threads or damaging parts
• Keep removed hardware organized and compare parts to the old screw for correct fit

This oven rack is a replacement wire shelf that supports cookware and bakeware inside the oven cavity, restoring proper spacing and airflow for even cooking and broiling. Ideal when the original rack is bent, rusted, or missing. What it does:

• Provides a stable surface for pans, baking sheets and cookware
• Restores correct oven spacing for even heat circulation
• Replaces bent, warped or corroded racks that catch or bind
• Enables use of multiple rack positions for different cooking needs

• Allow the oven to cool completely and disconnect power before installing
• Position rack with the rolled edges toward the oven walls and slide into desired rack guides
• Use gloves to avoid sharp edges and protect finishes
• Clean gently with non-abrasive cleaners; do not use oven self-clean while rack is in place unless rack is rated for self-clean cycles

A small replacement retainer clip that secures trim, panels or components in place to restore proper alignment and stop rattles or loosening. Fits original mounting points for a factory-style repair. What it does:

• Secures refrigerator trim, panels or small components to prevent movement and noise
• Keeps parts aligned so doors and drawers fit and operate smoothly
• Helps maintain grille, kickplate or interior trim attachment where clips are used
• Simple, non-electrical part — no wiring or calibration required

• Basic hand tools usually required; access the clip location before removal
• Remove any panels gently to avoid damaging surrounding trim or fasteners
• Replace only the worn or broken clip; align part fully before snapping into place
• Disconnect power to appliances with electrical components before starting work