Parts for Frigidaire EPWD15TS2: 03 - Pedestal Parts

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

This replacement mounting bracket secures components and panels inside compatible appliances to restore proper alignment and support. It's a simple, durable replacement that helps eliminate loose parts and rattling for safer, quieter operation. What it does:

• Supports and secures appliance panels, trim, or internal components to maintain correct positioning
• Prevents movement that can cause rattling, vibration noise, or misaligned doors/panels
• Restores stable mounting after original bracket bends, breaks, or corrodes
• Works where a small metal support or anchor is required for proper assembly

• One mounting bracket

• Basic hand tools typically required; visual inspection recommended before disassembly
• Turn off and unplug the appliance (or shut off power at the breaker) before starting work
• Retain mounting hardware if reuse is possible; replace fasteners if damaged or missing

Size: 6-20 x 0.312 inch.

This machine screw secures panels, brackets, and internal components in compatible appliances. Replacing a missing, rusted, or stripped #10-16 x 3/4-inch screw restores a snug fit and helps keep assemblies properly aligned and quiet.

• Fastens panels, brackets, guards, or other hardware in appliance assemblies
• Replaces lost, corroded, or stripped mounting screws
• Helps reduce vibration and rattling from loose fittings
• Maintains proper alignment and secure attachment of components

• Disconnect power before servicing; turn off gas and/or water supply if applicable
• Note original screw locations and any spacers or clips for correct reassembly
• Start threads by hand to avoid cross-threading; do not overtighten
• Use the appropriate driver or nut driver; wear gloves and eye protection

This door strike mounts on the appliance door and engages the latch/lock to keep the door securely closed so the cycle can start. Replace a worn or broken strike to restore reliable door closure and operation.

• Engages the door latch/lock assembly to secure the door during use
• Enables the control to recognize a closed door so the unit can run
• Wear or damage can cause a door that won't close, "door open" errors, or a unit that won't start
• Commonly damaged by slamming or misalignment; restores proper latching

• Disconnect power before servicing; also shut off the gas supply if working on a gas dryer
• Open the door, remove fasteners, and note the original strike orientation
• Install the new strike and tighten screws without overtightening
• Close the door to confirm a positive latch; adjust hinge/latch alignment if needed

This is a 10-16 x .312 sheet-metal screw with a quad-style panel head used to secure appliance panels and trim. It replaces missing or damaged screws to help stabilize panels and reduce rattling. What it does:

• Fastens control panels, trim pieces, and thin sheet-metal components
• Restores secure fit where screws are missing or stripped
• Helps stop panel vibration, rattling, or misalignment caused by loose fasteners
• Small, common mounting screw for interior and exterior appliance panels

• One 10-16 x .312 quad panel head screw (quantity: 1)

• Disconnect power to the appliance before working on panels or controls
• Use the correct screwdriver head to avoid stripping the quad head
• Tighten by hand; do not overtighten to prevent stripping or cracking panels
• Keep extra screws on hand; replace any that are corroded or damaged

The Drawer Latch is an OEM part for Frigidaire pedestals. This latch closes storage or pedestal drawers in the base. It creates a tight seal around each drawer, protecting contents from dust and spills.

Issues tend to arise from normal wear over years of use. Drawers opening and closing put stress on latches. Nearby laundry vibrations may also contribute.

Symptoms of a problematic pedestal drawer latch include:

• Drawers that do not fully latch or do not stay closed properly
• Gaps that allow debris or moisture to enter the storage compartments
• Loose or misaligned drawers that are difficult to open and close

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore ranges.

This leveling foot assembly restores a stable, level base so your machine runs smoothly and stays in place. It replaces a worn or stripped foot with a new bolt, pad, and nut to secure the adjustment.

• Levels and supports the appliance by adjusting the foot height
• Helps reduce vibration, rocking, and walking during operation
• Replaces stripped, bent, or rusted foot bolts and worn or missing pads
• Holds the set height with the included nut to maintain alignment

• Disconnect power; for washers, turn off water supply before servicing
• Carefully tip and support the appliance to access the feet
• Thread the new foot into the base, seat the pad, and tighten the nut
• Level front-to-back and side-to-side; ensure all feet are firmly on the floor

This dampener regulates airflow inside the refrigerator to help steady temperatures between compartments and reduce temperature swings. It replaces a worn or broken air control piece to restore proper circulation and consistent cooling. What it does:

• Controls airflow between fridge compartments to help maintain even temperatures
• Helps reduce warm or cold spots caused by stuck or broken dampeners
• Minimizes rapid temperature changes when doors open and close
• Operates quietly as part of the internal air distribution system

• Disconnect power to the appliance before starting any repair
• Basic hand tools may be required; handle plastic parts carefully to avoid breakage
• Verify correct orientation and secure mounting for proper airflow operation

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Hardware for pedestal