Waterndirt February 07, 2018 for Model Number SHEARF2UC/07 I'm stumped. Initial problem started with dishwasher not filling after starting cycle, no pumps, nothing. The digital timer WOULD count down to zero but dishwasher would do nothing for the 2 hours or so. (Each time I Power On dishwasher through each step below, I can hear relays clicking, along with the circulation / heat pump initiating and attempting to turn, a bit of a grunting sound from it, but nothing out of the ordinary. From memory, its always done that.) 1- Replaced fill valve. Everything worked fine for 2 to 3 cycles. Problem came back. 2 - Continued research and found a way to access Fault Codes and Customer service settings. Upon initial Fault Code runs, there were no codes given, each of the 8 cycles came back, E:00. Customer service program was run and it stopped after the Fill portion. Left with water at bottom of tub. 3- Continued research, attempted to start dishwasher cycle while using magnet at hall sensor at door, pulled up Float and drain pump engaged, draining tub completely. 4- Dishwasher worked again for a few cycles. Once it failed again, I ran more fault code and customer service tests. No fault codes, Customer Service test now acts strangely, locks up, all lights go on. 5- Ordered new control module and power module. After installation, dishwasher ran for a few cycles. 6 - Installed new float switch, even though current switch tested good. 7 - Dishwasher sat for a few days, I'm frustrated, more research, found out how to reset drain pump. 8- Dishwasher works again, for a few cycles. Stopped working, ordered new drain pump. 9 - Dishwasher doesn't work after installing new drain pump. Reset drain pump, dishwasher works for a few cycles. Now, Auto cycle has initial run time 1:59 hr. instead of 2:10 hr. and dishwasher ends cycle at :01 with soapy water in tub. Was able to use magnet and float switch to pump out water. 10 -Re-installed old control board and power module, unit was in DEMO mode, display read 1:23. Wasn't able to reset to normal mode using Bosch instructions, had to use Rest button. Once back in normal user mode, Auto Cycle displayed correct 2:10 run time. Drain pump turns on when starting cycle and then relay clicks, count down clock continues to run, no call for water. My last ditch effort would be to buy Heat pump. But at $200 plus, I'd just assume buy a new machine. All parts supplied by Appliance Parts Pros. Again, at no point has the digital display ever displayed codes, E:00 was always the result. Ryan
1 Answer Waterndirt, With the issues that you are having it sounds like you may need to check the wiring of the unit as this may be the most likely cause for this issue. If the wiring all checks ok the control module is the most likely cause for this issue. Read More...
Nick September 19, 2016 for Model Number SHE 3ARL5UC/07 Hi, When we turn this dishwasher on, it makes 3 different types of pump running noises & then says 'clean'. After several tries, it starts working. A mechanic came and said the motor needs replacing as it is like car starter, it starts working when gears are in the right place after getting several jerks. Reliable parts tells me that motor is in fact Heat pump 00705174 which is now 00655250. But your website says that it is not compatible with my model. Please let me know if indeed this is the part that needs replacing and if it is compatible with my model. Thanks
1 Answer Nick, The heat pump assembly 00705174 is showing as being the correct part for your unit. Read More...
Steve July 15, 2015 for Model Number SHE3AR52UC/07 My Bosch dishwasher no longer heats during the wash/dry cycle. The only part I see that heats is the heat pump part number 00655250. Am I missing something here or are there other troubleshooting steps I should take?
1 Answer Steve, You will want to check to see if there is power going to the heat pump assembly. If there is no power to it then the control module would be the issue. If there is power then the heat pump assembly would be the issue. Read More...
Richard May 22, 2015 for Model Number she3ar56uc/12 Is this part responsible for the water being pumped out of the basin and through the spray arms? The water comes in, the water will pump out, but the spray arms have stopped spinning with any force. Sometimes the water seems to get going and sometimes not. Is it possible that there is calcium deposits in heat pump?
1 Answer Hello Richard, This is normally caused by a stopped up filter or a failed circulation pump. You will need to remove the filters and ensure they are not clogged and observe the pump impeller for damage. Read More...
Mich October 22, 2013 for Model Number Bosch Dishwasher SHE3AR76UC/07 When the water is draining it sounds normal, I believe the drain pump to be OK. When in mid cycle it makes a whirring sound. I'm not sure if I can find a repair kit, impeller, for the pump or if I need to replace the heat pump assy. Can the pump be purchased separate from the heat pump assy? I've shop vac'ed the fitler area and the drain pump impeller looks and feels fine. is there a way to get a shop vac to remove the possible obstruction without disassembling the machine?
1 Answer Mich, Other than what steps you have already taken there would be no way to get into the pump assembly without disassembly of the unit. You would not be able to get the pump separate from the Heat pump assy 00705174. Read More...