Tom December 02, 2019 for Model Number FGHD2465NF1A Start button not working I can change all the other buttons by pressing them but the start button isn't starting it. It sits under a granite counter top which is too close for my fingers to fit in to hit the start button so I have been hitting it then closing it and it starts. The door switch is ok I've measured the voltage across it and when it's open the voltage is on one side then when it's closed it feeds through on both sides
1 Answer Hello Tom, in your model's handbook, it states to run a wash cycle; have the door open, select the wash cycle, then press start, then close the door. What you are doing to start a cycle is correct. Read More...
Aimee November 08, 2017 for Model Number FGHD2465NFIA We can not switch to "Sanitize" and now our dishwasher is starting to smell by not using this feature. Would I need a new control board or a console assembly to fix the problem? The dishwasher will run on the other cycles.
1 Answer Aimee, This issue would most likely be caused by a faulty console if the button is just not working. Read More...
Jennifer October 30, 2017 for Model Number FGHD2465NF1A I believe that our issue is due to a faulty console assembly, if we are not correct and it is the "Motherboard", is the console assembly returnable???
1 Answer Hello Jennifer. No, if this part is installed, it is an electrical part and can not be returned. Sorry. Read More...
Terry E January 05, 2017 for Model Number FGHD2465NF1A All buttons light up When I push the start button and close the door 99+,shows in the door. After five seconds or so the 99+ goes of and the Dishwasher has done nothing/ Give me some advise
1 Answer Hello Terry. Check the door switches and make sure they are good. If so, then the control panel 807545704 Is bad and will need to be replaced on the unit. Read More...
Christine W November 07, 2016 for Model Number FGHD2465NFIA Half the control panel doesn't light up and none of the buttons will make the dishwasher run. It appears to start to run and then blinks out.
1 Answer Hello Christine. You will need to order 807545704 for the control panel needed. If some buttons work and others do not, this is the issue. Read More...
Keith November 01, 2016 for Model Number FGHD2465NF1A My dishwasher does not work at all. I turned the breaker off for 1 hour back on and the display will give me PF for power failure. I checked the voltage to main board and getting 118vac. None of the control buttons work or light up. Thinking either control board or control panel any helpful hints to decide which one.
1 Answer Hello Keith. If you get a PF, then the board may be fine in the unit. It sounds like the control panel is bad and will need to be replaced. If the issue continues after replacing the panel then the manufacturer recommends replacing the board at that point. Read More...
Joe July 01, 2016 for Model Number FGHD2465NF1A The unit (Frigidaire dishwasher gallery series) is displaying an ER S with clean drying and washing all blinking. I turned the circuit breaker off for 30 minutes and after running the unit it gives me that error after a few minutes. Do I need to replace the control assembly or the control board?
1 Answer Joe, This issue would be caused by a faulty console assembly which would need to be replaced. The keypad on the console is stuck and you would need part number 807545704. Read More...
Carl August 01, 2015 for Model Number FGHD2465NF1A I have this dishwasher that needs a new part and I'm not sure which one. It failed for the person that bought it after a year and a few days. He told me that there was an error message and that it needs a new control box that sells for $125 Do I need a Console Assembly ? And is it true that this model tends to have this problem because of water erosion? Carl
1 Answer Carl, We would not know the specifics of what part that you are needing without knowing the error code. If it is the console then you would need part number 807545704. Read More...
Tony March 10, 2015 for Model Number FGHD2465NF1A My Frigidaire Gallery dishwasher keeps going to rinse cycle when I press normal wash, power wash, ect. No error codes. I con not change wash temp., or type of wash either don't work or reverts right back to the pre-set rinse cycle.Will the part I need be a control panel on top or a control board?
1 Answer Hello Tony. With the buttons not working, it sounds like the control panel is bad and will need to be replaced. Read More...