Victor Vella August 17, 2017 for Model Number EWF1246 I have an electrolux washing machine, EWF 1246 PNC 91451754601 The control pcb burnt out in a section, and the machine is not spinning at the end of the programm. Can you match a PCB for it? If I install a new PCB could there be a fault which burns it out again? I would appreciate an answer by email as well asI am going to be traveling and not always able to access the site. Thanks and regards
1 Answer Victor, your Electrolux washer appears to be an export model designed to operate in europe. Unfortunately, AppliancePartsPros.com Doesn't have access to the export model parts and service information for the Frigidaire/Electrolux products. Read More...
Michael November 09, 2015 for Model Number EIFLW55HMB0 I just replaced my control board (134640601) because the display was just flashing and would not take any input. The problem has not been fixed. Do I need to replace the front display now or should I try the motor control board? Or is there something else I should look at?
David L September 16, 2015 for Model Number EIFLW55HIW0 I have an Electrolux front load washer EIFLW55HIW0 and I'm having an issue. Over the past month the front lights all seemed to be on but at a very low level even when the washer was not running. 3 days ago the washer just wouldn't turn on. If left unplugged for 3 to 4 hours it sometimes will turn of and if placed into diagnostic mode error code 97 (console or main board control problem) is present. The wiring harness from the front console to the control board all test good. Is there a way to isolate which of the two components (Front control or main board) is faulty? David
1 Answer David, There is no real way to test to see which component has failed as far as main control or the User interface. Based on the manufacturers recommendation you would want to replace the main control board 134640601. Read More...
Denise May 26, 2015 for Model Number ewflw65hiwo We had something stuck in the drain filter - which caused a LOUD noise. It was a nail. Cleared that out. Then also fixed the tub hose which caused leaking on the floor. (that was happening for awhile, was not sure where it was coming from until we took the top off etc... to clear the drain filter). Put it all back together. NOW this is a new problem. The display turns off mid cycle - or at the beginning, or just won't turn on at all. It is not the electrical outlet, or the breaker. I am worried that it may be the control box? We were able to get it through install cycle a few times, but it is erratic and we just can't use it now. I am not sure if I need another NEW part? Or if there is some reset. (I did the reset to factory settings on the display) The display is FINE, when it comes on. It just stops on its own. Any suggestions????
1 Answer Denise, This issue does sound like it would be caused by a faulty control board but would recommend putting the unit into a service diagnostic mode to see if there are any stored error codes. These codes if there are any will point you in the direction of what to check. This information will be located on the tech sheet located in the unit. Read More...
Dan September 22, 2014 I have a Electrolux front load washer and lighting struck my house a week ago...ever since then the washer will not power on. I recevied the front control panel from electrolux and installed but still nothing.
1 Answer Hello Dan. It sounds like the main board or filter board is bad. We will need your model number to help you with this. Please call 1-877-477-7278 or post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Tony August 10, 2014 for Model Number EIFLW55HMBO I HAVE A CODE E 32 . I was able to unplug the machine and reset it. Does not put enough water in the washer.
1 Answer Hello Tony. What you need to do is make sure the drain hose isn't kinked at the back or blocked. Then empty the filter at the bottom of the washer and clear the chamber out as well. Make sure its fully cleared out in there. Once that's fine then take off the pressure hose which goes from the pressure switch down to the pressure bottle at the bottom. Check these hoses and make sure the hose is fine and there's no splits in there or holes. If so then replace the hose. Also make sure the pump impeller at the back isn't jammed up as well. Make sure the pump is working also. If all that appears ok and the pressure switch has been replaced already then it may be a faulty control board. Read More...
Anna May 26, 2013 for Model Number 970-C480420 The control panel lights up but the machine wont start. It keeps showing "pause".
1 Answer Hello Anna. Make sure the door switch is good. If so, you will need to order and replace the interface on the unit. Read More...
Wes July 03, 2012 for Model Number EIFLW55HIWO The motor doesn't run. The motor controller #E307807, model 1346182. Will AP5270208 replace this motor controller? (134640601). THANKS!
1 Answer Wes, part number 134640601 is the main control board. For the motor control board use part number 5304504715. Thanks! Read More...