Tammy September 04, 2021 for Model Number LEQ1442ES0 I turn on the dryer and it runs 30 seconds to a minute then shuts off. Why?
1 Answer Tammy, if the door switch is operating properly and the vents are clear, the failure would most likely be the main control 134484212 if the display turns off as well. Read More...
Jim September 21, 2020 for Model Number leq1442es1 My frigidaire dryer model leq1442es1 would start the cycle then after a few minutes it would start beeping and the lights would star flashing, then it would shut down. I tested the themostats, heater coil, fuse and motor switch. Everything checks out. So I replaced the board, and now it won't heat. I checked everything over again. And everything checks out, except I checked the red and black heater wires on the back of the board and found there is 120 v going in on the red and nothing coming out on the black. So then I unplugged the red and black wires from the relay and put in a jumper and turned it on and the dryer started heating. So I checked the continuity of the relay with the dryer on and found nothing. I'm really stumped. Any ideas?
Jerry January 04, 2019 for Model Number LEQ1452KS0 All this occurred over time: My dryer would run but sometimes not heat. I fiddled moving buttons around and it would heat on timed settings either low or medium, I use. Then, the dryer would beep occasionally and stop heating. At some point, the dryer would just start beeping w/o being touched. When ready to dry, I could still manipulate the buttons to get it to heat on timed settings. Last week, I did the troubleshooting with Select and Cancel/Pause then Start and Cancel/Pause - but could not count the beeps. The dryer was beeping more, so I unplugged it. Plugged it back in but Now, it won't start. The selection lights are responsive but nothing will make it run - at least it used to run even when it didn't heat. Also, not getting any troubleshooting beeps Start and Cancel/Pause as I was getting when moving knob to 2 o'clock position. I think it is the control board but want advice.
1 Answer Jerry, Based on the information provided this will most likely be caused by a faulty control board 134484212. Read More...
Pitbull May 04, 2018 for Model Number 134345000 My control board doesn't power up. The control board number is 134345000. I was wondering if the control board 134484212 is compatible with mine.
1 Answer Hello Pitbull, I'm sorry but we will need to ask you to post a new question including the model number from your units' I.D. tag so we can recommend parts that can be guaranteed to work properly on your unit. Thank you for your patience and understanding in this matter. Read More...
Lance R February 17, 2017 for Model Number feq1442ES0 Hi - my dryer rarely heats when on the low heat setting. Everything seems to run properly, but there is no heat (back of dryer is room temperature, clothes are wet). Other heat levels work. Leaving it unplugged seems to "reset" it, but it stops heating again after a load or two on "Low". Replaced that high limit and the thermistor (the variable resistance heat sensor). I'm thinking the heat level knob might not be connecting properly on low. Any better ideas?
1 Answer Hello Lance. Check the knob and if it is good, you will need to replace the board on the unit. Read More...
Carl February 06, 2017 for Model Number Fase7074lw I'm getting a e61 error runs for awhile and shuts down Service man said the control board is not available how can that be its only 5 years old. Can you help me
1 Answer Hello Carl. The board is available for your model. It is part number 137260620. Read More...
Emily November 14, 2016 for Model Number Frigidaire FGQ1442ES0 Dryer runs for awhile and then shuts off before load is actually dry. After running test getting error code 95 on my Frigidaire FGQ1442ES0 dryer but don't see it on the code sheet from the manufacturer. Also in the past have been receiving error code 62 after same issue describe above, however after running the test it is no longer coming up. Please advice proper action/parts need to fix problem.
1 Answer Emily, This may have been a E25 and would indicate a control NTC Open circuit. Remove wires from control thermistor. Measure resistance of thermistor. If reading is not 50 K (± 10%), replace thermistor. If reading is within 50 K (± 10%), check wiring between thermistor and electronic control. If good, replace electronic control.. Read More...
Tony March 11, 2016 for Model Number LEQ1442ES1 Hi There, I purchased part # AP3844555 control board for my Fridgidaire dryer model #. LEQ1442ES1 serial # XD84409698. DIY video it shows that the indicator lenses (parts #'s 7 & 8 did not come with the part. However 2 of the 3 of these lenses have 1 of the end of these arms that are broken off. Also the black turn shaft on the main dial that sets the dryer times and type is missing on the new part and I don't know how to remove this from the old unit. I don't want to break it. This part shows that it is on the new part in the video Can you help supply the lenses and guide me on what to do with the black control dial shaft. Thanks in advance Tony
1 Answer Tony, It appears that the black shaft should have come with the control board but if it did not then the black shaft should just pull straight out. For the light pipe number 7 on the diagram it is part number 134429100, number 8 in the diagram is part number 134429200. Read More...
1 Answer Hello Pat. We will need your model number to help you with this. Please call 1-877-477-7278 or post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Jrmb72980 March 12, 2015 for Model Number LEQ1452KS0 When I put in the clothes, after clearing the lint filter, the dryer operation begins fine. However, after 10 to 15 minutes, all the lights start blinking and the operation stops. It also appears there was hardly any heat inside the dryer. What needs replacing? Thank you.
1 Answer Hello JRMB72980. You need to check the heating circuit and make sure it is good in the unit. If so, check the control board in the unit and all the wiring in the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...