Unclegeorge November 25, 2015 for Model Number FPGF3081KFB Frigidaire gas range, control panel partial failure, some numbers work, some don't."Cancel" is also failing. Could ask "membrane or controller and membrane", but see one questioner lost his membrane replacement after two years. Is replacing the entire unit recommended? How often, if ever, is a simple disassemble and cleaning effective? What life might I expect the repair to have? Range is only 4 years old, disappointing failure. I note the new Frigidaire ranges have a more tactile pad which clicks on press.
1 Answer UncleGeorge, You can take the ribbon harness loose and check to make sure that there is no corrosion on it. If this does not correct it then the membrane would be the model likely cause of the issue 316549105. Read More...
Kelly November 08, 2015 for Model Number fpef3081kf Range I replaced the control membrane two years ago and it has become unresponsive on most things.
1 Answer Hello Kelly. It sounds like the control 5304478041 will need to be replaced again. Read More...
Minnie April 10, 2015 I have a Figidaire Gallery slide in stove/oven. I have 2 problems. 1. On the stove top, one of the burner lights (that shows the stove is hot) is on all the time. This is not a big deal....but would be nice to fix if not too expensive. 2. The light does not work on the oven control board. It has been slowly fading, and if the sun wasn't too bright I could barely see it.....now I cannot tell anything. The oven works, I am just unable to read anything on the panel. My stove is approximately 15-16 years old. My husband will need to provide the model number later today. I am just wondering what type of part we need to purchase. Thank you!
1 Answer Hello Minnie. For the light you must replace the infinite switch that is causing the light to stay on. As for the display, you will need to order and replace the control board on the unit. Read More...
Beth August 31, 2014 for Model Number FPGF3081KFC Hi - this is a 6 year old range. The "cancel" button does not respond to touch, and the "Set Clock" button is becoming less responsive, no matter how hard it is pressed. Everything else (clock, all other buttons) currently work. Do you think this is a problem with the membrane only, or the entire control panel? Thanks.
1 Answer Hello Beth. Based on the information you provided, you will need to order and replace the membrane 316549105 on the unit. Read More...
Steve August 30, 2013 for Model Number FPGF3081KF My convection fan and electric convection element in this gas stove do not get power, everything else works fine. I ordered the main control and membrane from you guys, changed it all out, and have the same problem. What else could cause this? The fan turns freely by hand, ohms out at 80, the element at 42 ohms, and checking with the multimeter, there's no power getting to either one. You push convect (350) then start, the convect bake light is on, oven heats up with gas, but no fan........Thanks!
1 Answer Hello Steve. If you replace the relay board 5304476749, the you will need to replace the control 5304476749 on the unit. If you replaced the control, then replace the relay board. Read More...
Luis August 12, 2013 for Model Number FPGF3081KFE I have a range with the controller board No. 316562004, damaged by liquid spill, the membrane is damaged too. Is this the right replacement part for both? Thanks.
1 Answer Luis, on your model the manufacturer does not offer the controller with membrane on your model FPGF3081KFE. The controller is part number 316562004 and the membrane is part number 316549114. Thanks. Read More...
Steve June 26, 2013 for Model Number FPGF3081KF This is a very nice range, and everything works great except the convection fan seems to never run. I checked ohms on the fan motor at about 80, and put a 110v jumper to it, and the fan spins with power applied. Could the cause be anything other than the main board?
1 Answer Steve, If you turn on the convection fan and there is not power getting to the fan then the oven control 5304476749 would be the problem and would need to be replaced. Read More...
Larry June 15, 2013 for Model Number FPGF3081FKA On the touch control pad buttons do not work. Specifically I can not turn the broiler or the preheat on. Is the problem the Interface board or is there something else I can check. How do I get the panel to display error codes?
1 Answer Larry, The error codes cannot be recovered on this unit. If there are error codes it will display and normally will not be able to use the oven. You will want to check to make sure that the ribbon harness on the from the control to the membrane to make sure that it has a firm connection and also check to make sure that there is no corrosion on the harness. If this checks ok then replace the control 5304476749. Read More...
Cyndi May 19, 2013 for Model Number FPCS3085LFB The appliance keeps beeping and shows error code E014 what can be done to fix this? I have already turned of the unit overnight and that did not help.
1 Answer Cyndi, The EO14 indicates a loss of the display or keyboard. You will want to check the P1 connection on user interface the P2 on the Userinterface and the J@ and J8 on user interface. Read More...