Raj December 25, 2012 for Model Number fef366ebc I have frigidare stove model fef366ebc and I need front left burner coil. What is the part no and availability and can I get repair help if I want to replace it myself?
1 Answer Raj, the front left element is part number 316135401. Remove power. Remove door. Get the lower front lower screws out that hold the top to the trim plate. Lift up and support the top. There is a mount plate that bolts both front burners onto the lower side of the top. Remove wiring, keeping note of where each wire is located at. Reassemble in reverse order. Thank you. Read More...
Don May 15, 2012 for Model Number TEF361GSA The right front burner stays on high no matter what setting I use on the infinite switch. I have replaced the infinite switch AP#3885460 and the problem remained. Would suggest ordering a new element?
1 Answer Hello Don. Yes, if the wiring on the unit is good, and the switch is new, you will need to replace the element 316135401. Read More...
Don May 14, 2012 for Model Number TEF361GSA Right Front burner stays on high no matter where I turn the switch, I already replaced PN 316436001. It did not help. The switch will turn it on and off.
1 Answer Hello Don. Check and make sure all the wiring is good on the unit. If so, and the switch is new, you will need to replace the element 316135401 on the unit. Read More...
Eman April 22, 2012 for Model Number FEF365BWC I have Electric frigidaire range and I am looking for one knob and the front-right element burner.
1 Answer Hello! The burner control knob is part number 316223002 and the right front element is part number 316135401. Thanks! Read More...
Amir January 30, 2012 for Model Number 165n8-16056r I got this model number off a Frigidaire Stove it looks like this one here but not exactly where can i find it?
1 Answer Hello Amir! We will need your appliance model number to verify the correct part used on your appliance. You may use our model/serial number location tool to help you locate the model number on your appliance. Here is the link, thanks! http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Steve January 17, 2012 for Model Number 316224201 I removed the burner (Big eye) from my glass top stove because it blow out. I can see the burn mark where it broke apart. I kept my old burners from my last glass top stove and was wondering if I can use one of the burners from my old stove. The piece (Don't no name)that is sticking out of the burner has two smaller ends that you plug the wires in from the stove. My old one has two bigger ends which two of the wires from the stove want fit in. If I change the wires to bigger end to fit my old burner, will it cause damage or will it heat up?
1 Answer Hello Steve. No, you will need to order the correct element needed for the glass top and not the old one that is different. Most elements are different sizes and watts and will not interchange unless the model numbers of the ranges were the same. Hope this helps. Read More...
Terry K January 15, 2012 for Model Number fef366esh I need this burner element for my model fef366esh I need to know how to remove the glass top.
1 Answer Terry, "The procedure for servicing the smooth glass cooktop and surface elements is the same as in previous models. The front of the cooktop can be lifted by removing the two screws that secure it to the range chassis(in the top of the oven door opening). With the cooktop in the raised position the surface heating elements, warmer zone element and their wiring connections are accessible. The top can be held open by using a wood or plastic prop rod approximately 28 inches long. 1. Before removing the element be sure to note the locations of the element mounting clips in the support channel slot. The replacement element must be installed in the same position. 2. Carefully remove the wires from the element. Take note of the terminal identification on the element terminal block for each wire connection. 3. Before the element can be removed from the support channel the locking tab on the mounting clip must be closed 4. Remove the mounting screw that secures the element support channel to the cooktop. by squeezing shut with a pair of pliers. After the repair is complete the tab can be re-opened by using an awl or similar instrument. 5. Carefully pull the support channel away from the cooktop far enough to disengage the element mounting clips from the channel. Slide the element out from between the support channel and the cooktop. Reinstall or replace the element by reversing steps." Good Luck and Thanks Read More...
Austin V. September 05, 2011 for Model Number FES367DBA What is the difference in burner 15A and 15B? They are both 9" burners with different prices and part numbers.
1 Answer Hello Austin! 15A is the left rear element listed as an 8" 2200w element, part number 903118-9010. 15B is the right front element listed as a 9" 2500w radiant element, part number 316135401. Thanks! Read More...
Wayne September 01, 2011 for Model Number FEF364DSA I need "dummy Proof", instructions to install new 9" surface element.
1 Answer Hi Wayne. Either behind the control panel or behind the lower storage drawer there is a supplied wiring diagram supplied with your unit. Remove power. Remove door. Get the lower front lower screws out that hold the top to the trim plate. Lift up and support the top . Mark all screw holes with a felt marker that you will take off pertaining to your particular burner. There is a mount plate that bolts both front burners onto the lower side of the top. Use the wiring diagram and / or mark the wires so you will replace them on the burner exactly correct. You also need to keep in mind how to re-mount the burner so you have it centered with the top opening so your pan will heat correctly. Reassemble on reverse. Thank you. Read More...
1 Answer Hello Dusty. Which element on the stove top uses the simmer feature? If it is the center, then you will need to order 318198825. Hope this helps. Read More...