Jason October 02, 2022 for Model Number efls527uiw I have a E11 code. Went into diagnostic mode, and all solenoids turn on and reach the correct volume of 140cm. I was able to blow air down the pressure switch air line so It is not clogged. But when i try to run a normal cycle, No water is pumped in. Does the pressure switch not work during diagnostic mode? it filled to the correct level in the manufactures notes. It is a fairly new model, manufacture date 2019. Do you think its the pressure switch or the controller board? Thanks!
1 Answer Jason, Based on the information provided the E-11 code means the washer took too long to fill. It could be one of three problems, either the machine isn’t filling with water, or won’t fill with enough water or it has a draining issue. The following things could cause the error... The water tap is closed. Your water pressure is too low. The drain hose isn’t in the correct position or isn’t at the correct height. The inlet hose valve filter is dirty. The drain pump and filter need cleaning. The drain is blocked. The air tube is kinked. You used too much detergent. The pressure sensor is defective. The inlet valve is defective Read More...
Tina April 30, 2022 Water continues to flow into my washing machine even after it should be done with that cycle. Water continue in through all cycles and after. Just started happening. Is there a seal that needs replacing that stops water at appropriate times?
Raymond March 04, 2022 i got few questions ask ..here..anyway..do you check pressure switch # 134762010. some jhow? .or you don't.. or just replace it...thanks..
1 Answer Hello Raymond, this type of pressure switch is electronic (analog) it is powered and read (varying voltage output) by the control board, there is no practical way to test it. Read More...
Raymond March 04, 2022 ok..i got frigidaire washer. model # fafw3921nwo. i got error code e32. & i couldn't fine out that code . so want no what. mean...my washer won't spin completely.. al other are good...belt. etc...so..thanks
1 Answer Hello Raymond, the code refers to the control board seeing a fault in the water level pressure switch, since it does not know if all the tub water has drained completely this can affect the spin cycle. The switch is part 134762010, you should first check the drain pump is working, and the airline tubing from the tub to switch is not restricted. Read More...
Raymond B. March 03, 2022 for Model Number Fafw3921nwo Frigidaire washer doesn't drain water all out & it doesn't get to full fast spin. Thanks
1 Answer Hello Raymond, The unit will not go into the high-speed spin if it does not drain the water out completely. You will need to check the drain pump for foreign objects and debris. Also, check the hose from the tub to the pump and the hose from the pump to the standpipe. If nothing is found in the pump area or hoses, the pump 137240800 will need to be replaced. Read More...
Nancy May 25, 2020 My Frigidaire front load washer will start and then dr pops up I have replaced the door lock and it will no longer latch. The new latch was identical to the old one
1 Answer Nancy, To be able to assist with your question, we will need to have the model number of your unit. Please provide the model and resubmit your question. Read More...
Gerald W January 29, 2018 for Model Number FAFW3511KR0 My front load washer flashes that it is in pause. What originally happened is I put in a load for normal wash, started the cycle, the door lock engaged and the cycle started. About 1 minute into the wash the cycle just paused and is still flashing paused. I've tried cancelling and restarting another cycle, but it goes back to a paused mode. Any idea what could be going on? Thanks
1 Answer Gerald, You will want to check the door lock to make sure that it is engaging properly. Also try putting the unit into the diagnostic mode to make sure that there are no stored error codes. Read More...
Tod S. January 18, 2018 Have a front loader frigidaire not receiving proper water amount can you help
1 Answer Hello Tod, you'll want to check the pressure tube for any obstructions as well as any kinks. If that looks good you'll want to check the screens on the water valve for any debris. Hope these tips help you locate the issue! Read More...
Birgit November 09, 2017 for Model Number FAFW3921NW0 I have a Frigidaire affinity no FAFW3921NWO . The display shows pause and when I hold 5 sec start/pause and cancel so it’s coming Eoo. The washer does nothing. The water is still in the washer!!! We do all the steps with pull out the cord and wait, but nothing helps
1 Answer Birgit, Showing a code of E00 would be an erroneous code and would most likely be caused by a faulty main control board. Read More...
White X. October 23, 2017 Is there a way to check whether a Water Level Pressure Switch 134762000 is operational? It has labeled 5V, GND, and OUT signals. If 5V is connected to 5V and GND, what is expected on the OUT? Assume voltmeter or oscilloscope available to check.
1 Answer Hello White, One wire is voltage, and the other wire goes to the water valve. When the switch is satisfied, the voltage is sent to the motor through the third wire. In other words, the switch completes through one set of contacts while the other set is open. When the switch is satisfied and opens, the other set closes. Both will never be opened at the same time. Read More...