Paul September 28, 2020 for Model Number GUD27ESSM/27GSSM JUST PURCHASED A 27" INCH STACKABLE WASHER/DRYER FROM LOWES. (NOT YET DELIVERED) ON ORDER. WHAT IS THE I.D & O.D & LENGTH OF THE DRAIN HOSE. NEED TO POP A HOLE AND MAYBE EXTEND THE HOSE. WANT INFORMATION ON ORIGINAL HOSE SPEC'S AND MAY NEED TO EXTEND THE LENGTH. THANKS, P.J.
1 Answer Hello Paul, you may have to wait for the appliance to be delivered for that information as the manufacturer does not supply that information even in the Installation Instructions that come with the appliance according to the manufacturer's website. Read More...
Roger March 24, 2019 I have a ge drain hose that's too short and I need an 8 foot hose. My model number is gcwn2800d1ww. Does GE make them longer?
1 Answer Roger, your model does not have a longer drain hose listed for compatibility. However, the extension kit [WH49X301] would work to get the drain hose to the length you need. Read More...
Gary December 08, 2017 for Model Number GTD695SMJ2ES I need an extension to attach to existing drain hose because it is too short. I don't want to have to pull the dishwasher out to attach a longer hose. what extension hose should I get?
1 Answer Gary, Unfortunately we are not showing a drain hose extension that will work for a dishwasher drain hose. Read More...
El Dee May 26, 2017 Hi there, I managed to get the WH49x301 extension hose fitted and clamped onto one end of the drain hose but am having trouble with the other. There was a kink and it leaked, I trimmed the damaged bit and am now having difficulty getting it all to fit together. Have tried a bit of soap as per someone else's suggestion. Is there some sort of trick to get these two parts connected? (Also finding this an absurd way to correct a manufactures defect, the original hose is ridiculously short, grrr...) Hoping you can help as this is causing serious marital discord!
1 Answer El Dee, have you considered a longer drain hose GPF10L . In most cases, you need to trim the end of the corrugated hose off straight as possible. insert the end of the hose into the opening of the hose extension, as far as possible, it should be a tight fit, you may have to twist the hose to help seat it in the extension, Usually we would wrap the "splice" tightly with electrical tape, then install and tighten a worm gear hose clamp over the connection, just a 1/4 turn past finger tight. this will reduce the possibility of leaks from the spliced area. Read More...
Paul P. January 31, 2017 for Model Number GTW680BSJWS What drain hose extension kit can I use to extent the drain hose on my washer? Will it attach to the existing hose and extend from there? I need to add at least 6 feet to the hose that it comes with.
1 Answer Hello Paul, WH49X301 is the only drain extension recommended by GE. It is not recommended to use more than one as this will affect the units' wash result. Read More...
1 Answer Hello Dan, This information has not been shared by the manufacturer. From counting the one inch squares in our photo of the part, it appears to be between 36 and 40 inches long, (as a guess). Read More...
Swda1 December 13, 2016 for Model Number A511 This model is for Maytag washer. I had been frustration finding a part number for a hose from pump to siphon assembly, but I can't find it for part number to order a new replace! Can ya find me a correct part number for it? Thanks for your time!
1 Answer Swda1, The part you will be looking for is the drain hose which is part number WP22001448. Read More...
Sahm August 04, 2016 A video showing how this attaches to WH41X10096 would be helpful. If you want to end up with a longer hose with the inlet to the machine at one end the gooseneck to put into the plumbing drain at the other the original hose will have to be cut and the extension spliced into it. Where is the best place to cut the original hose (WH41X10096) and what tool should be used to make the cut? And why does GE make such as stupid flimsy short plastic tube for a drain in the first place?
1 Answer Hello SAHM. There is a video for replacement on the parts page. As for where to cut it for the extension, There is a non corrugated section you will cut and clamp. Read More...
John April 03, 2016 for Model Number GE - GTWN4250D1WS I need a longer hose for my GE washer. I would like 12' if possible.
1 Answer Hello John, GE lists a 12 foot dishwasher drain extension WD24X10065. Be aware there should be no loops before the drain. The length should be maintained to countertop level until it drops to the sink drain/disposer connection for proper operation. Read More...
Rita February 23, 2016 for Model Number GTW485ASJWS The drain hose is too short. Is there an extension I can purchase?