Scott September 09, 2011 for Model Number DBSR453GBOWW I have a GE dryer model DBSR453GBOWW that started making a loud noise when the drum started rubbing. I took out the drum and the O-Ring on the rear drum bearing kit was broke. Do I need to replace the entire bearing kit, or can I get away with just putting on a new O-Ring? In your experience does a bad bearing kit cause the O-Ring to crack, or can the O-Rings just go? Thanks!
1 Answer Hello Scott. Based on the information you provided, it sounds like the bearing kit WE25M40 is the best choice for repairing the unit. Hope this helps. Read More...
Jerry S August 26, 2011 for Model Number DVL223EAOWW We bought this dryer used. Looks like it is about 10 years old. It worked fine for about two months but was getting very hot to the touch on top at all temperature selections. I t also left scorch marks on clothes especaily white clothes. Now it does not run at all. It only makes a humming noise. Looks like I get resistance at the timer selectoer switch and the on/off switch. The humming noise comes from the motor from what I can tell. The dryer heat still works. I can turn the drum but it makes some noise. Also sounds like something is almost rolling along with the drum itself. I am wondering if it the "drum slides' I see here or the rear bearing itself. Also how do I get to the parts. I cannot tremove the back. I can remive the top and yhaven't tried to remove the front. Any and all hewlp would be apprecited. Only got $65 invetsed and would be willing to put another $50 to fix it if possble. Thanks again.
1 Answer Jerry, Hope you haven't damaged the motor ? once you've got the top up, You'll find two 1/4 " screws near the top on the cabinet frame interior, remove those screws, and lean the top mof the panel out, disconnect the door switch wire harness and lift up and out on the front panel. You'll see and inspect the front drum glide/seal assembly attached to the door opening of the front panel WE03X10001 . Once you have the front off, you will need to reach in through the cut out in the front frame and release the drum belt from the idler pulley. You then grasp the drum, and lift up on the back portion of the drum, to disengage the drum bearing shaft from the composite drum bearing WE25X10001 , and slide the drum out of the cabinet. You should vaccuum and dust out the complete interior and all the components, then re assemble the dryer. Thanks and Good Luck Read More...
Shay August 20, 2011 for Model Number DBSR453EB2WW my dryer started squeaking loudly, it still dries great but only with a loud constant squeak. I have replaced the front bearings, the back bearing looked very good when I complared it with a new one. what else could be making the very loud sound?
1 Answer Shay, The noise could be from the idler pulley WE12X83 But, The rear drum bearing could "look" good and make a squeaking noise. You may want to start there first. Good Luck Read More...
Matt July 21, 2011 for Model Number NWSR483EB3WW I Have a GE model# NWSR483EB3WW, Making a loud squeaking noise when drying. is the part i need to fix this the (Rear drum bearing kit, part#AP2619300) any other parts that could cause this loud squeaking noise?
1 Answer Matt, Yes, most of the high pitched squealing noise(s) are from the drum bearing assembly WE25M40 on that style dryer. There is the possibility that the idler pulley WE12X83 or the belt WE03X29897 could be making the noise as well, but not likely based on your post. Thanks and Good Luck. Read More...
Kathleen R. July 06, 2011 for Model Number dbxr453ev2ww I got the heater housing, and I can't read your diagram to install ground strap between retainer and element housing. Can you plesae provide a readable sketch. I read that, the screws for the bearing retainer are tap in,is this correct?
1 Answer Kathleen, you're correct, all the mounting screws in the bearing kit are "self tapping" screws, it really helps the process. As for the "grounding" strap WE1X1172 , that is installed and mounted,with the rear bearing retainer plate WE1M300 using one of the mounting screws(insert the screw through the opening then mount the strap so the other opening is in contact with the pointed end of the drum bearing shaft, to achieve the gounding effect. You'll do fine, Thanks and Good Luck. Read More...
Mike June 28, 2011 I have purchased part #AP2619300, rear drum bearing for my GE Dryer. The supplied back plate does not accept the screws supplied or the screws from the prior back plate. Is this common, do I need to drill out the holes a touch more or can I use the old back plate?
1 Answer Hello Mike. These are self tapping screws. The holes in the plate are not threaded, the screws will be tight when installed. You do not need to drill out the holes. Hope this helps. Read More...
Mike H. June 10, 2011 for Model Number DDE7900 GAL Hello I purchased a Rear drum bearing kit AP2619300, on the old bearing it had a washer and a keeper slide on spring washer and the new one does not, is the rubber in that slot all I need?
1 Answer Hello Mike. The manufacturer discontinued both the old parts on the washer and replaced it with this kit. The kit includes all the parts you need to replace the bearing, thanks! Read More...
1 Answer Hello Bob. You will want to hear where the noise is coming from. If you determine it's from the rear you will want to install kit WE25M40. Since you will have the unit apart, you might as well install a new set of slides. You will need two WE03X37318 and two WE03X37317. Also make sure the front bearing WE14M124, where the slides mount to, is not damaged. Hope this helps! Read More...
Mansoor May 09, 2011 for Model Number DPSR473GW0AA Gas dryer /Ser#: VT736023A This dryer is making a loud squeeking noise after a couple of minutes of starting and keeps making the noise until it stops. Not sure if I have to change the front bearing/rear bearing or the rear seal. How to tell what needs changing and if you can provide a link to the steps of going about making the repair.
1 Answer Hello Mansoor. Here is a link to our Repair Forum, this is a free service to our customers. Use this link to access the repair for your question. Hope this helps. http://forum.appliancepartspros.com/dryer-repair/162473-front-bearing-replacement.html Read More...
Lee M. May 02, 2011 for Model Number dde5700gblwh Squeeky bearing that I worked some grease into a few months ago, but the noise is back after one month. No matter how I position the cabinet it usually stops squeaking for a few minutes, and then the squeak comes back.
1 Answer Hello Lee. Yes, WE25M40 will work on your dryer. According to the serial and model it was manufactured in 1988 or 2000. It gave both dates. Hope this helps. Read More...