Bruce April 08, 2013 for Model Number JBP24B0B4WH 1 of the top heating elements burned out, I do mean burned out it went on fire. I am going to replace the element and the terminal block, but the the light on the stove to warn that a surface element is on stays lite now. By replacing the element and terminal block will the light go out? or do I also have to replace the temperautre control reostat?
1 Answer Hello Bruce. Most likely the switch will need to be replaced along with the element to get the light to shut off on the unit. Read More...
Vicki Miller December 19, 2012 for Model Number RB757WH4WW I have recently purchased a replacement baking element. The original one exploded while I was baking. When I went to replace it, I found that the spade terminal that connects to the baking element also was damaged. I have not been able to purchase the yellow wire that connects from the terminal block to the baking element. I am tired of being told that this is a non-consumer part. It is a simple wire with connectors. I have been using the stove top so I know that nothing else is damaged and I know I have seen the wire kit for sale but can not find it now. Can you please help me find the replacement wire?
1 Answer Hello Vicki. The wires is not available, but you can order new terminals TJMA02875-1 and crimp onto the existing wire in the unit. Read More...
Jeff December 06, 2012 for Model Number JBP24BOB4WH serial # sd103436Q I can't find the model number for my stove listed, will this terminal block work? If I drop the o from bob4wh this in the number that comes up, is this right? Thanks for your help.
1 Answer Hello Jeff! Yes, you will use model JBP24BB4WH in search for parts. Yes, the terminal block kit WB17T10006 is the correct replacement and will fit your unit. Thanks! Read More...
David November 15, 2012 for Model Number JSP34 WOW3WW I thought I bought all the right parts put my element does not sit flush in the burner drip pan.
1 Answer Hello David, the burner elements for your model are, 6 inch element WB30M1 and 8 inch element WB30M2. Hope this helps! Read More...
Tom A March 23, 2012 for Model Number JSP26BW3AD drawing ref number 82 The kit installed easily but the black block does not contain a brass assembly for the burners to plug into similar to the original.
1 Answer Tom, The brass assembly, that the burners plug into are on the end of the wires. Basically you insert the brass connector end of the wire into the slots on the back side of the black plastic receptacle until they "lock" into place. Splice the new wires to the original wires using high temperature, porcelain wire nuts, if the wires are not long enough to reach the infinite switch, install the drip pan and insert the element ends into the slots of the new receptacle. Everything should be fine from there out. Thanks and Good Luck Read More...
Chris L. March 09, 2012 for Model Number JBP35EK1BB I just purchased the terminal block kit AP3203326. Which of these 2 wire nuts is the the right size for the kit: AP3440631 or AP3440673?
Ralph P. February 25, 2012 for Model Number J BP24G R1 WH How do I access where the stove end of the element wires in kit # WB17T10006 attach?
1 Answer Hi Ralph. Removew power. Then all coils and drip bowls. Then remove the connector bracket screws from all 4- burners. Then open the door and remove any hidden screws under each front corner. You can now lift the top and drop the prop rod down to support the top. Replace one terminal wire at a time so you have rewired it exactly original. Place all wires routed together so they do not have any contact under the burners to short them or to burn them out. Terminal kit part # WB17T10006. Thank You. Read More...
1 Answer Hello Chris! No, the terminal block kit WB17T10006 does not include the wire nuts. For medium wire nuts use part number TJMA01165-1 and for large wire nuts use part number TJMA01166-1. Thanks! Read More...