Walter September 11, 2015 for Model Number LGWM2501HWA Which door do we need to order for our model of washer? The plastic in the front door is badly cracked after two years of normal use. Thank you
1 Answer Hello Walter, You will need to order part number 3581ER1008V for the model number provided. Read More...
Don C. May 11, 2015 for Model Number LG - WM2501HWA I need the outer door plexi-glass for this model washer. What is the part number for this outer glass?
1 Answer Don, the outer glass is included with the door assy, part number 3581ER1008V. Thanks! Read More...
Gianfranco April 04, 2014 for Model Number WM2650HWA Is it possible to buy the small gray spring piece at the bottom of the door assembly? I think it's used to told the door slightly ajar when washer is not in use. Mine I think snapped and doesn't stay inside the hole when opening the washer door.
1 Answer Gianfranco, The part that you may be referring to is the magnetic holder AGM73610701. If you pull the part up at Appliancepartspros.com there is a picture of it so that you can make sure that it is what is needed. Read More...
Dave March 15, 2014 for Model Number WM2016CW I want to confirm that the front door assembly AP4322486 had the upgraded magnetic door assembly that hold the door ajar while not in use to air out the washer drum and that this door will fit my LG front loader washer model WM2016CW
1 Answer Dave, Based on the manufacturers site the door assembly has not been redesigned and has the same part number as the original part. The part number for the door assembly is 3581ER1008Z. Read More...
Bob July 14, 2013 for Model Number WM2501H*A Just need the inner door glass just broke no reason. Need part # please
1 Answer Bob, The door glass cannot be purchased separately and you would need to get the complete door assembly 3581ER1008V. Read More...
Cindy December 02, 2012 for Model Number lg front load washer model wm2016cw replacement glass The glass broke on the door of this washer, just need the glass, not the whole door. What is the part number?
1 Answer Hello Cindy, this door assembly 3581ER1008Z is the only way the manufacturer supplies the door. You cannot get just the glass. Usually this is because of the assembly process. The way it's put together at the factory may not make it possible for the individual to get it back together properly without a machine or special tools. Thanks! Read More...
Richard P. October 19, 2012 for Model Number LG WM2455HW WASHER Hi, The door seems to be comprised of a clear plastic outer window, a round door frame assembly, and a large inner glass window. On my washer door, the clear plastic outer window is cracked. I don't know how it cracked, the washer is housed and babied in its own little room. Any ideas? The more important question: is the clear plastic outer window available as a replacement part or do I have to purchase the entire door assembly? Thanks, Richard P.
1 Answer Hello Richard, From the research I have done, the door glass and plastic are not available without ordering the door as an assembly 3581ER0001P. Read More...
Rick October 17, 2012 for Model Number wm2277hw My inner door is cracked, it has been for a while. I recently experienced a large leak, came home to a laundry room floor full of water. Could this be anything other than a complete door assembly? Does the door assembly come as one piece that I can change out, or is it many pieces that I will have to assemble? Thanks
1 Answer Hi. Yes the inner door crack will allow the leak if the door boot seal part # 3581ER1008Z does not seal against the door perfectly. It will leave water traces for show if this is where the leak is from. If you have a lower cover door for the pump, then make sure the pump is not clogged. Release the tubing on the back side of the cover into a bucket. Once all water is drained then you remove the pump cover and clean the catch and pump impeller area so it drains correctly. If the pump impeller is loose on the shaft then replace the pump part # 4681EA2001T. Thank you. Read More...
Brad September 24, 2012 for Model Number WM2277HS The washer is leaking on the rinse cycle. Also the inner glass on the door is cracked. What part is just the inner glass on the door? Is there a gasket that needs replaced also on the door?
1 Answer Hi. The whole door assy. part # 3581ER1008Z is the only way you can replace the inner door cover crack. Remove the back panel and see if the drain hose part # 5215ER2002G has a pinhole leak. Look at the door boot part # 4986ER0004F inside and at the 6:00 position to see if it has a rip in it as well. Thank You. Read More...
Juan C July 30, 2012 for Model Number WM2277HS Water leaks when the machine is on rinse. Noticed that one of the plastic parts inside the door hinge area was cracked. Is there any other reason why water leaks or is this the problem? If so, what is the part number for them as I can't find them. Also, my dryer that goes with this washer model does not heat as quick as when it was new. Can you tell me what I need to do to fix it? It takes a lot more time to dry than normal. Thank you for your time.
1 Answer Juan, This may be the part you're looking for 3212ER1016A based on your post information. We wouldn't expect a major leak, so you may want to consider checking or replacing the water level switch 6601ER1006E and air dome hose 5214FR4125N this could allow the washer to overfill and leak, in the rinse cycle. As for the dryer, first thing to do is disconnect the exhaust vent pipe and check and clean all the lint and debris from the inside of the pipe, and check the vent hood as well. Thanks Read More...