Gabi February 05, 2025 for Model Number LG WM2801HLA I have been searching for this boot gasket and believe it is the right one (https://www.appliancepartspros.com/lg-gasket-mds47123601-ap4998888.html). I have seen many and order one that have said they are the correct one for the model, but they have holes on the side that my machine does not have tubes for or have an additional hole on the top. All I need its 3 holes in the top (2 for dispensing, one for the light) and a drain hole in the bottom. Please let me know if you believe the one I have found to be correct or not. Thank you in advance.
1 Answer Gabi, the door boot gasket MDS47123601 is the correct one for the model number provided. Read More...
Peter September 01, 2024 for Model Number LG WM3270C I’ve just purchased a replacement MDS47123601 door seal for my LG washing machine. Part number was taken directly from the old seal. The old seal has molded outlines at the top of the seal, but no holes. The replacement seal has 3 holes, 2 small round one larger D shape in the top side. How do I order the correct seal?
1 Answer Pete, Based on the model number provided and both of its revision numbers the part number for the Gasket is: Gasket MDS47123619 / MDS47123619 {WM3270C - ABWETUS or WM3270C - ABWEVUS} Read More...
Laurence April 24, 2024 for Model Number Wm3050cw There is. No./00 or /01.@after.part number what.is.in.it is mds47123601 da21 is what is.in.there currently which.doesn't match.what lg says. there is a a short connector at bottom and there are NO holes cut out on top. I.cannot.find it . It.is.stock.and gas never been.replaced please advise.
1 Answer Hello Pyingling, yes this is an LG model however it seems to be an Export model and we have no parts listing for it. Read More...
Pyingling March 16, 2023 I ordered that part and they sent me MDS47123601 No14 on it and the holes are not the same. Mine says MDS47123601 DA23 Please advise ty
1 Answer Pyingling, unfortunately, a model number would be necessary so that the most accurate information could be provided. The following link can be used to assist in locating the model number of your appliance. https://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Pyingling March 16, 2023 I need a replacement for this part # MDS47123601 DA23. I can't find a model number anywhere. Please advise
1 Answer Pyingling, the gasket MDS47123601 currently shows as being available as of 03/16/2023 and can be purchased through the item information page. Read More...
Lance October 11, 2022 for Model Number WM3050CW Is MDS47123601 gasket/seal interchangeable with MDS47123602? One place said they were. Please verify.
1 Answer Lance, While these 2 parts appear to be the same it would be recommended to use the one the manufacturer states is for your unit. There may be a slight size difference that we cannot tell. Read More...
Yury October 28, 2021 for Model Number 79641583410 Looking for the correct door seal/boot/gasket from my Kenmore Elite washing machine 796.41583410. The original gasket has part number molded on it as MDS47123601 NO.15. The part on your site does not have the no.15 in the model number. Will it fit? Here's your stock number: AP4998888
1 Answer Yury, According to the model and the manufacturer's parts list, the gasket for this model will be MDS47123608. Read More...
Joanna October 11, 2021 for Model Number LG. WM3670HVA I have an LG Washing Machine. The Front Bellow Gasket needs to be replaced. I ordered the part MDS47123601. The last four digits of this part also have DA 20 Next to the part #. However when ordering the part, the last for digits are not show. A part arrived and it was MDS47123601 DA 18. It was too big. Need MDS47123601 DA 20 . Do you have it? Thanks!
1 Answer Joanna, According to the manufacturer, the correct door bellow for your unit will be part number MDS47123619. Read More...
James June 16, 2020 for Model Number MDS47123601 I can't tell from the photos but does this one have the holes for the sensor and steam holes cut out or not? Because mine does not.
1 Answer James, " does this one have the holes for the sensor and steam holes cut out or not?" No, the MDS47123601 / MDS47123601 Gasket does not have the holes cut out. It does have the three(3) molded gasket drain holes in the bottom of the gasket so water and moisture can return to the tub and drain out. Thanks, Read More...