Tony D December 29, 2014 for Model Number mdb7809awq2 Turned dishwasher and it was running when I went to bed. In the morning many of the control panel lights were on but the washer wouldn't run no matter what button I pushed. Could that be the thermal fuse,control panel or both?
1 Answer Tony, The thermal fuse would not be the issue with the unit, if it was faulty then the unit would not have any lights on at all. The most likely cause for this issue would be a faulty control board. Read More...
Ed December 15, 2014 for Model Number kud101ilbl6 The dishwasher lights blink but the machine will not work. Do you think it could be a fuse or the control panel?
1 Answer Hello Ed. Make sure the door switches are good. If so, you will need to order and replace the control panel on the unit. The fuse is good. Read More...
Harry December 03, 2014 for Model Number KUDP01FLBL3 If the fuse is blown will this cut the power to the user interface so that none of the lights will light?
1 Answer Hello Harry. Yes, if the fuse is bad, there will be no lights on the control panel. Read More...
Rudy R. October 24, 2014 for Model Number 655-16579201 Timer starts at 88 minutes and will go down to 78 minutes and stops there. Also water will not drain
1 Answer Rudy, The model number listed is not coming up as a valid model and we would need this to properly assist. Please post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Dan October 11, 2014 for Model Number KUD01-FL-BL I have a follow-up questions about replacing the wire harness with the fuse. I've seen that the harness needs to be replaced with the fuse or the fuse will blow soon. My question is WHY? It doesn't make sense to me. The original fuse didn't have a separate harness, and it doesn't seem that the harness makes any difference electrically anyway. If someone understands this, please explain (do not just restate that the harness needs to be replaced). Thanks!
1 Answer Dan, The harness has to be changed as the manufacturers engineers redesigned the part and was included due to safety issues that could arise by not putting the wire on. It is most likely because of connection issues. with the original harness that was shooting the fuse. Read More...
Bob October 07, 2014 for Model Number GU1500XTKB0 Dishwasher was not drying properly, then stopped running completely. I did a reset and it ran again once, now the rinse only is blinking. If I cut off the power and then turn it back on it has a "2" on the display and goes thru what sounds like a cancel/drain cycle, then back to rinse only flashing. The heating element and thermostat show continuity, the thermal fuse also shows continuity but appears to have been scorched, it also won't reset again.
1 Answer Bob, The issue is in the control panel / key pad assembly WP8269464 . there's a faulty key pad circuit causing the control to remain in the rinse cycle. When you reset the control, it will operate one time. once it sees the faulty circuit again, the board will revert back to the failed mode. Once you replace the console, and reset the control, you should be fine. Read More...
Tony October 03, 2014 for Model Number KUDS01FLSS2 Is There a reset somewhere ? I get no lights, no nothing.
1 Answer Tony, Unfortunately, No there is no reset circuits or switch. But you're on track, if you're sure you have 120 VAC to the dishwasher in the junction box, then the next step is to access the thermal fuse in the control console and check the fuse 8193762 for a "closed" circuit. You can also check for voltage in and out of the fuse, if you wish. Read More...
Mary August 14, 2014 for Model Number KUDI01ILBL3 Does the replacement dishwasher fuse kit # 8193762 fit this model. Thank you.
Chris F August 13, 2014 for Model Number GU2400XTPS6 I am replacing the fuse in my dishwasher for the second time. The first time, I didn't realize that the wire harness also needs to be replaced. While I hope this will solve the problem, are there other places that I need to check that might be causing the fuse to blow? Thanks. Chris
1 Answer Hello Chris. It is required to replace the harness with the fuse. This should solve the issue. Read More...
Judy M. June 09, 2014 for Model Number 665.13482K902 I need to order the fuse kit for my Kenmore dishwasher. The one that looks like the replacement says it is incompatible for my model. Can you tell me what part number I need? Thanks
1 Answer Hello Judy, You will need to order part number W10258275 for the model number you listed. Read More...