David February 12, 2020 for Model Number MTW5840TW0 i need to replace the hose from part 24 in the diagram to the drain tub i can not feel a clamp on the hose how do i get this apart or is it one whole piece going to the pump?
Sharon February 22, 2018 for Model Number WTW5200SQ0 I recently moved into a new home. Because of the location of the washer box , the drain hose is too short. Is there an extension kit for this particular model?
G April 21, 2017 for Model Number LSQ9030PQ5 My model number is. Correct. Your video is not therefore I am not sure that the drain hose is correct. So here I am waiting to figure out your website THEN after I wait I get to buy maybe the. Correct part from you and have nothing to follow as far as a repair manual this is NOT the way to run a business
1 Answer G., The WPW10096921 / WPW10096921 Drain Hose is the correct part number for the model number you supplied. Your machine is different than the video you viewed. If you need to replace the hose, you'll need to remove power to the washer, slide the washer out and remove the two screws from the back of the control panel end caps, and flip the control panel up so you can access the cabinet clips in the rear corners of the top panel. Raise the rear of the cabinet slightly and slide the cabinet off the frame and set it aside. Disconnect the drain hose from the bottom fixture of the drain pump, carefully remove the drain hose "bucket" from the rear panel and extract the assembly from the washer and panel. Then remove the existing drain hose from the bucket, insert the replacement hose and reverse the procedure . Restore power and check the washer for operation and leaks(you may want to have a large bowl ready when you remove the hose from the pump, it will expell any remaining water in the hose and pump). Read More...
Deborah B. October 10, 2015 I have a washer and the brand is Inglis. It is about 5 years old and I need the long hose that goes from the bottom of washer. I don't have a part number. I need the longer hose.
1 Answer Hello Deborah, I'm sorry but we will need the model number from the units' I.D. tag to look up any parts that we can guarantee will work on your unit. Thank you for you're patience and understanding in this matter. Read More...
Terry July 31, 2015 for Model Number LAT9206BAE Hi, I need to order a drain hose for my MAYTAG Washing Machine, Model number LAT9206BAE but I am not sure of the part number. Any help would be greatly appreciated. Thanks!
Donna March 15, 2015 for Model Number WFW9400SZ01 I was wondering if this drain hose will fit my wash machine? Thanks!
1 Answer Hello Donna! No, the drain hose WPW10096921 is not compatible with your model. According to the model number given the replacement drain hose is part number WP8181737. if needed, you can extend the drain hose using kit part number 285863. Thanks! Read More...
Steve June 05, 2014 for Model Number wtw4810bq0 I need at least an 8' drain hose. It would be nice if it had an elbow to take an immediate turn out of the base of the washer so I could avoid a 'sweep' turn and push it close to the wall. Ideas?
1 Answer Steve, you can use the extension kit part number DRNEXT4 to extend the current hose on your washer by 4 feet. Thanks! Read More...
Susan November 27, 2013 for Model Number MTW5740TQ0 I have tried to order a drain hose for my washer and I can only find 42 inch hoses. The hose that came on my washer is 92 or more inches long. Where can I find one?
1 Answer Hello Susan, WPW10096921 is the drain hose listed for the model number you listed. There is a 42 inch extension available as part number 40922. Read More...
Joe C. June 23, 2013 for Model Number LSQ9549PW I need to replace the drain hose in my whirlpool washer. It's a single hose that runs from the pump to the drain. The old one appears to be 7 or 8' long. Can you confirm the correct item I need? Thanks!
1 Answer Joe, your model uses drain hose part number 285664. For a longer hose use part number 285666. Thanks! Read More...
1 Answer Hello Jodi. Remove the hose from the pump and the clip from the frame. Then you can remove the hose from the unit. You may need to lean the washer back to complete the repair. Read More...