Gordon February 06, 2017 for Model Number WMH1162XVB-2 No heating, light, or fan, but control panel works. Fuse, Door switch, or something else? Thanks
1 Answer Hello Gordon, This sounds more like either a door switch W10211972, W10269458, W10211974, or control board WPW10211457 issue. If the fuse W11707984 blows or the thermostat W10269232 goes open, the control display will not illuminate. Read More...
Pol N. February 03, 2017 for Model Number 6009-80A I accidentally plugged my unit to 220 volts. Now it's not working anymore. Did I blow the fuse or the motor?
1 Answer Hello Pol, This will have to be troubleshot with a test meter to determine what part or parts have been damaged. There can be more than one part damaged from this high voltage. Read More...
Joyce October 01, 2016 How do you get to the magnetron in a Whirlpool Microwave Model MH7140XF? Thank you.
1 Answer Hello Joyce. You will need to uninstall the microwave and remove the outer cover off the unit. Once the outer cover is removed, you can access and replace the magnetron in the unit. Read More...
Larry May 25, 2016 My Whirlpool 2006 microwave model MH 1160XSB-O will not heat up. Everything else is working. I thought it might be a fuse, but I am unable to locate it. I took off the control panel on the side of the front, but did not see it. Any suggestions on where the fuse might be? Thank you.
1 Answer Hello Larry. You will need to remove the outer cover off the microwave to access the fuse in the unit. Read More...
1 Answer Hello Annebell. You will need to disconnect the power and remove the outer cover off the unit. Now you can access and replace the fuse in the unit. Read More...
Rudolf January 06, 2016 for Model Number whirlpool over the range Where is the fuse located on the Whirlpool over the range microwave?
1 Answer Hello Rudolf. It is located in the control panel section of the unit. You will uninstall the microwave to access and replace the fuse in the unit. Read More...
Antonio B November 17, 2015 for Model Number Microwave oven West band Microwave is working perfectly but is not heating.
1 Answer Antonio, You will want to check the magnetron on the unit. Unfortunately we would need to have the model number to be able to assist properly. Read More...
Brennan November 17, 2015 for Model Number YWMH1162XVS-1 I have a 5 year old over-the-range microwave oven, model YWMH1162XVS-1. It stopped working on me yester day. The clock and keyboard still worked but when I tried to enter cook time or the +30 second quick start function it would state something like “open and close door”. I tried that several times for 15 minutes and it kept refusing to start. I disconnected it from the power a couple of times, waited a minute, and tried again. No luck. So then I went to Google and started researching and found that my door switches may be the culprit. With the unit still attached to the wall, I open the control board/keyboard and had little access to the switches. I took out the T10 screws and got the switch holders out. The top unit had 2 switches – looking in, the left switch had 3 terminals hidden behind the plastic bracket, and the right switch had 2 terminals and was much easier to access. I wanted to check the resistance and took them out of the bracket (support interlock top #8206419) and broke the clips. ARGH! The clips also forced the 3-terminal switch to separate in half but it appeared to go back together with no issues. I tested them on an auto-range ohm meter and they appeared to work. Both switched also appeared to pass the “click” test. So, I have a half open OTR microwave, a cranky wife, and a broken support interlock top #8206419. Where do I go now? What was the first thing I should of tried – the 20 amp ceramic cylinder fuse? Any advice would be much appreciated.
1 Answer Hello Brennan. You will need to check the door switches on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Mary August 21, 2015 for Model Number MH1150XMS3 Can you tell me what the Cu. Ft. is for this model? I have looked in the book and on the unit and could not find it. Maybe I overlooked it.... Thank You
Roxanne August 05, 2015 for Model Number Sears Kenmore 665.6062200 The microwave "dinged" after heating up a cup of coffee. When I walked over to it to get my coffee with was dark, no lights no nothing. We were told it might be the fuse and to try plugging it back in and then pushing the "clock" button. Sure enough it lit up but then almost immediately went dark again. Any ideas?
1 Answer Hello Roxanne. Check all the wiring on the unit first. If all wiring is good, then it sounds like the board may be bad on the unit. The board is discontinued and no longer available. Read More...