Lashon October 29, 2012 for Model Number mgr5755 My oven door will not close completely. I was told that I need door hinges. What is the part number for door hinges on model number MGR5755?
1 Answer Lashon, it would depend on your full appliance model number. What is your full appliance model number please? Thanks. Read More...
Ljubica February 29, 2012 for Model Number mgr577oada Can you tell me how I can remove and install new hinges on my oven door?
1 Answer Hello Ljubica. Remove the range top and remove the 7 phillips screws from either rear edge that secures the side panels to the back of the range. Remove 3 screws from the top edge of the side panels on this gas model and pull upward and remove thr side panel. Now you can access and replace the door hinge WP74011141 on the unit. Hope this helps. Read More...
Lisa January 21, 2012 for Model Number MGR5750AW Door hinges are broken on our Maytag oven( model MGR5750ADW). What steps do I need to take to replace them? Thanks
1 Answer Hello Lisa. You will need to raise the top of the unit and remove the back and side panels to access and replace the hinges. The door lifts off the unit to replace the hinges WP74011141. You will need to door to be at the first stopping point to lift it off the unit. Hope this helps. Read More...
Anthony P. October 03, 2011 for Model Number MGR5750ADW 2nd Request...I purchased 2 hinge assemblies for Model MGR5250ADW....Are there any easy steps to install these hinges? Does the inner oven housing have to come out? The oven door is off..HELP please
1 Answer Hello Anthony. Remove the door from the oven. Then remove the screws securing the hinges. Once removed, you will tilt the hinges WP74011141 and work them out of the body of the range. Reinstall in reverse order. Hope this helps. Read More...
Anthony P October 03, 2011 for Model Number MGR5750ADW I want to replace both hinge assemblies.can I buy a LEFT and RIGHT assembly and does the entire oven interior have to be removed to replace the hinge assemblies? Also is the hinge mounting screw or bolt come with the assembly?
1 Answer Anthony, Both the hinges are the same, so you will need to order 2 WP74011141 , not a left and right hinge. First, remove power to the range. You will need to remove the oven door, Open the door to the broil stop grasp the door on both sides and lift up and slide the door off the hinge assembly. You will then need to remove the cooktop burners(label the burner location first, twist the burner 90 dgs. counterclockwise and raise up on the burner, label and disconnect the igniter wires. Remove the two phillips head screws holding the burner bracket to the underside of the cooktop, then lift up on the front corner(s) of the cooktop and raise and remove the cooktop. Remove the three screws holding the side panel to the frame and lift up on the side panel until the "key hole" retainer disengages from the bottom of the frame, and set the side panel aside. You will have access to the hinge, remove the hex head screws from the front flnge of the oven and remove the hinge. Thanks and Good Luck Read More...
Richard V. October 02, 2011 for Model Number MGR5750ADW Is the part #AP4101300, Oven door hinge, the same one for both the right and left? It looks the same as the one that I removed.
1 Answer Hello Richard! Yes, the oven door hinge part number WP74011141 can be used as the left or right hand side hinge for the oven door. Thanks! Read More...
Lowell August 26, 2011 for Model Number MER5780BAQ Only half the question was answered, how do I access the hinges?
1 Answer Hello Lowell. Remove the door from the oven. Then remove the screws securing the hinges. Once removed, you will tilt the hinges WP74011141 and work them out of the body of the range. Reinstall in reverse order. Hope this helps. Read More...
Lowell B. August 26, 2011 for Model Number MER5780BAQ I have noisey hinges when the oven heats up. Can they be lubricated, and how do you get at them to lubricate or replace? Instructions for another model posted don't seem to apply.
1 Answer Hello Lowell. Yes, you can lubricate the hinges with high temperature grease TJ17001004. You will need to remove the hinges from the oven and put it on the rollers and spring hooks. Also any joints will need to be greased as well. Hope this helps. Read More...
C. Jones May 22, 2011 for Model Number JGW9130ADB How can I replace the oven door hinge? I bought one from this site, it looks exactly like the one on the right side of the oven. There is no way to get the new one into the left side slot ? And get the old left side out ? Is this an in shop only repair? Thanks
1 Answer Hello C. Jones. Here are the instructions from the manufacture. Hope this helps. 1. Open the door to the stop position. 2. Lift the door up and off the hinges. 3. Remove the two 5/16 screws holding the hinge to the frame. 4. Pull the hinge forward through the opening of the frame. Read More...