Harold B. November 01, 2011 for Model Number 106 626662 My Ice Maker On My Kenmore Stoped working. I put pressure on the Gear that says do not rotate. and it works for a little while.and then stops working. I noticed the center of the gear the tab that locks it in place is broken. Can you sell me a gear and a center peace. THANK YOU
1 Answer Hello Harold. They do not offer just the gear for your model, you will need to order the icemaker 4317943. Hope this helps. Read More...
Bob October 14, 2011 for Model Number w10190965 The replacement part # AP4360346 did not come with the wire on/off control. Is there an extra cost for that and what part numer is it? I am supprised it was not included.
1 Answer Hi Bob. Sold much cheaper is the stripped down version ice maker. You will use the front white cover, wire harness and the bail arm off your old unit. It pulls out of the ice maker and make sure you push it in fully on the new one. The bail arm is part # W11342242. Thank You. Read More...
Sandman338 August 10, 2011 for Model Number ap4359694 control module My control module is bad. Looking at the price difference there appears to only be a 30 count difference between a new control module and a new ice maker. Is this correct or is there no control module in ap4360346?
1 Answer Hello! Typically, when purchasing items as a kit they tend to be a less price or a little more than purchasing parts separate from the actual kit. The icemaker WPW10190965 will include the module. Thanks! Read More...
Phil M. July 25, 2011 for Model Number whir lpool side by side mod.no.ed5fhexnt00 Follow up from my previous question concerning wiring harness, is this what you needed?
1 Answer Hello Phil. Yes, that is the correct model number. Based on the model number you provided, 4317943 is the correct icemaker for your refrigerator. Hope this helps. Read More...
Phil July 23, 2011 for Model Number ims 106 626662 Will the wiring harness and connections be the same on the part number ap4360346? It seems the long wiring harness on the currant one doesn't unplug at the rear or back of the freezer. Rather the existing harness plugs into the front of the icemaker, just behind the grey head. Wiring harness remains connected to my freezer. Will this work?
1 Answer Hello Phil. You can disconnect the wire harness from the module of the icemaker and install you wiring harness inside the freezer. We will need your model number to determine if this is the correct icemaker for your refrigerator. The one you provided is not working. Hope this helps. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Joel July 21, 2011 for Model Number AP4360346 I installed the icemaker part AP4360346 listed as a replacement for my original part 626661 last night. Overnight the ice tray filled with water but that is all, it didn't dump the ice. What is the problem?
2 Answers Hello Joel. Check and make sure the bail arm WP627792 is down and installed properly. If not, the icemaker will not dump the ice. Hope this helps. Read More...
Joel July 21, 2011 for Model Number AP4360346 I installed the icemaker part AP4360346 listed as a replacement for my original part 626661 last night. Overnight the ice tray filled with water but that is all, it didn't dump the ice. What is the problem?
2 Answers Joel, What was the original problem ? If you can supply us with a complete model number, we can direct you to other necessary tests and checks. We'd appreciate it. Thanks. Read More...
1 Answer Hello, this icemaker is the complete assembly. It will include the drive gear located in front of the icemaker. Thanks! Read More...
Bill June 04, 2011 for Model Number KitchenAid model KSBP25FKSS02 Installed ice marker W10190965 in my KitchenAid Refrigerator. It made one batch of ice over night and this morning the shut off arm was in the up position. I moved the arm all the up and backdown and it went through another cycle and dumped the ice. I arm again stuck in the up postion. I left it there for several hours.
1 Answer Hello Bill. Based on the information you provided, it sounds like the icemaker bail arm return system is bad, and you will need to replace the icemaker WPW10190965. Hope this helps. Read More...
Jimmie June 02, 2011 for Model Number '04 Kenmore icemaker 626662 or maybe 628370? I found a "modular ice maker service sheet" attached to frig with part #628370. But tag on front of ice maker says 106-626662. Anyway, the plastic shaft that turns the big plastic gear broke. What do I need?
1 Answer Hello Jimmie! You will need to replace the ice maker. Your part number is WPW10190965. Thanks! Read More...