Tim February 23, 2020 for Model Number JDB1270AWY Installing lower door gasket - The old one just fell off, So I ordered a new one and it does the same thing. Falls off as soon as I close the door. I then tried using gorilla glue in the groove. That helped, but it's still loose and the door wont stay shut.. It "snaps" in, but easily falls off.. Seems like it should stay much more firmly.. Ideas?
1 Answer Tim, That gasket does just push in unless the inner door panel grove is stretched out. If this is the case you may have to replace the inner door panel. Read More...
Hugh October 06, 2019 for Model Number DU1300XTVB3 Is there a lower door seal for my dishwasher DU1300XTVB3? It looks like there isn't one. I replaced the rubber gasket seal around the door frame, but could there be another source of leaks?
1 Answer Hugh, It does not appear that there is a lower door seal on this unit. If the unit is leaking look for a cracked or clogged spray arm, also check for the unit filling with too much water. These would be the most likely causes. Read More...
Heather July 17, 2019 for Model Number MBD8951AWS When I replace the old bottom door seal with the new one, the new one slips off just like the old one did?? The groove does not seem to stay tightly on the edge and the piece comes right off when I shut the door. Please help.
1 Answer Hello Heather, the lower inner door seal is a snap on fit. If it snaps in place but comes off when door is opened/closed check the inner lower front of the tub for any build-up /residue that may be pulling it off. Also check the door hinges for wear that may be allowing the door to ride lower. Read More...
Jerry April 11, 2019 Good morning, I need to order the piece that slips into the back of the door when laying horizontal . can you tell me the difference between the bottom door seal and the trim door seal
1 Answer Jerry, We will need your model number to help you find the right parts for your unit. Please post another question with all your info included thank you. Read More...
Bob December 22, 2015 for Model Number fridgedar Dishwasher leaks only once during the entire cycle. I replaced the bottom seal and the seal around the door. Whst else could it be ?
1 Answer Bob, Check the spray arms to make sure that there are not breaks or clogs in the arms. Also check the water level to make sure that it is not filling too high. Also check to make sure that the vent is not leaking by opening the door and see if there is moisture in the door. Read More...
Glenn G November 02, 2015 for Model Number JDB1090AWS How do I install the bottom door seal on the Jenn Air dishwasher. Part # 99003045
1 Answer Glenn, The bottom of the door panel has a slot in it that is holding the seal. You would pull the old seal out and push the new seal into the groove. Read More...
Teran October 15, 2015 How do I install the bottom door seal? the old one came completely off, so I don't know which edge goes in first. Does the bent edge get pushed up into and under the sharp edge of the bottom of the door?
1 Answer Hello Teran. It installs on the bottom of the inner door panel. The old one slips off and the new one slides onto the lip. Sometimes it is easier to remove the inner panel to install this. Read More...
Gary February 14, 2015 for Model Number SHY56A05 UC/14 (FD8301-) How do you attach the inner door to the springs?
1 Answer Hello Gary, The springs are connected to the door hinges with the tension roller assembly 00618605. Read More...
Charles C. September 23, 2012 for Model Number MDBH750AWB My dishwasher leaks at lower left corner when running. I have checked all the seals. If I push in on the door, while running leak stops. Just replaced latch. Seems new latch does not hold door shut at tight as old one. Is there adjustment? Striker OK. Puzzled. Have taken apart 3 times to check everything and I am baffeled...
1 Answer Hi. Remove the lower kick panel. Remove the lower rack and use a torpedo level for leveling. Front to back on the rack rail and side to side on the opened door /tub lower area. Look underneath and make sure all 4-legs sre sung touching the floor. If the tub is not first leveled the door seal will not work. If you decide that you have opened inner dishwasher cabinet opening then yopu may decide to lower the front legs a liitle morer( 1/2-half bubble) and this tilts the front up slightly so the inner door seals agaqinst the door seal part # WP99003337. Open the door and feel the inner door raised ridge to see if there are nicks or gouges where the leak occurs. Look at the door seal as well for the same. Whipe the inner door seal area dry with a towel. Start the unit and let it run for a minute. SLOWELY open the door so you do not sling water out. Look at the inner door to see whewre the leak is and flings out the side. If there is no evidence then replace the inner door lower seal part # WP99003045. Make sure all seal area's are clean so it can seal. The door hinge does not adjust. Thank You. Read More...
Walt January 14, 2012 for Model Number jdb1250aws My dishwasher is approximately 3 years old, it has started dripping at the bottom of the pull down door [main door] this dripping is enough to wet the drawer beneath the dishwasher, and runs down the front of the drawer to the floor, which part or parts are most likely my problem. It only leaks when the dishwasher is running.
1 Answer Walt, A couple of easy checks to make first. Check the corner edge trims , and tub bottom trim, make sure they're in position. and the bottom door seal for damage or deterioration. check and make sure the door panel is not bowed or bent, with a straight edge in the seal contact area of the door, remove and check the lower spray arm for cracks in the seam or debris in the jet opening of the arm. Good Luck and Thanks Read More...