Jake October 03, 2020 for Model Number WFC150M0EW Oven will not heat up past 130 degrees, changed oven temp sensor and same issue. What is next part to change or troubleshooting step?
1 Answer Jake, with the power cord unplugged, it would be recommended that the bake element is tested for 24O and the broil element is tested for 16O of resistance. If the elements test properly, then the failure would likely be in the oven control W11122555. To ensure that the correct element part numbers can be obtained, the full model number would be necessary as there is a small difference. Read More...
Carolyn September 16, 2020 for Model Number WFE374LVS MY RANGE OVEN AND THE DIGITAL DISPLAY WILL NOT WORK. THE DIGITAL DISPLAY WILL NOT LIGHT UP. THE OVEN WILL NOT WORK BECAUSE I CAN'T TURN IT ON BECAUSE OF THE DISPLAY. THE STOVE TOP WORKS FINE., WHAT PART DO I NEED?
1 Answer Carolyn, you have a few tests to run. First, check your incoming power to the stove to be sure you have 240v. If so find your wiring diagram and see if the clock/control is getting 120v. If so replace the clock, if not check that diagram for any thermal cutoffs or fuses that are in line before the clock power. One of those could have failed to cause loss of power to the display/control. Read More...
Mariana August 24, 2020 for Model Number maytag MGR7661WW transfer all orifices from gas to lp propane but my oven is shooting off and F2 appears on the screen, I think the oven sensor is the problem wrath is your expert opinion thank you very much
1 Answer Hello Mariana, F2 is a stuck keypad fault code, on your model the keypad is part of the control board assembly, WPW10271767. Read More...
1 Answer Hello, James. Get to the oven sensor disconnect plug and check the plug itself. Then check the sensor's resistance. At room temperature is should be around 1100 Ohms. It it's way off then replace the oven sensor p/n AP6016450. Thank you. Read More...
1 Answer Hello Joe, according to that code the control board cannot read the temperature in the oven through the temp sensor. Using a multimeter check the oven temp sensor for about 1090 ohms at room temp, next check the temp sensor wiring to the control board, if both check ok replace the control board. Read More...
1 Answer Hello Marge, I'm sorry but we do not have a video for that specific model. The temperature sensor is accessed inside the bake compartment and you remove the two screws to remove it. You will then carefully pull on it and carefully fish the connector through the opening. If it comes loose behind the panel you will have to pull the unit out and access it by removing the rear panel of the range. Read More...
Ap January 27, 2020 for Model Number MGR7662WS4 Broiler and range work fine. Problem is that when baking, the oven cannot maintain a temperature greater than about 350. Heats up to 350, then the heating just shuts off and doesn't restart. Slight smell of gas.
1 Answer Hello AP, if the oven bake burner comes consistently when the oven is cold, and the problem only occurs with hot oven, check the oven door is holding in the light switch. If ok then inspect/clean the mounting of the bake burner to the chassis. Clean area with light sandpaper and snug mounting screw but do not strip it. Retest oven. Read More...
Donna December 13, 2019 for Model Number WFE520SOFSO MY OVEN IS GETTING TOO HOT AND THE TOP ELEMENT IS GLOWING EVEN THO THE TEMPERATURE HAS BEEN REACHED. THROWING CODES E1 AND F6. I FLIPPED THE BREAKER AND RESET HOPEFULLY TO HELP WITH THE F6. E1 I GUESS I NEED A NEW OVEN TEMP SENSOR. ???? I WANT TO MAKE SURE I GET THE RIGHT REPLACEMENT PART...
1 Answer Hello Donna, the fault code is for an oven over-temperature condition, in bake mode, the broil element relay located on the main control board is stuck closed, the repair would be to replace the control board W11267090. Read More...
Randy August 09, 2019 for Model Number SF376LEKQ Oven works fine except when we try to bake for an extended time, like a turkey; also, when the food item requires a starting temperature and then a lower temperature for the remainder of the cook time, the oven doesn't maintain the heat.
1 Answer Randy, The model number you supplied is incorrect or incomplete. But, based on your information the oven temperature sensor would be a very good and logical place to start. The sensor can lose its calibration with age, usage and high heat cycles or numerous self-clean cycles. The temp. sensor would be the place to start. Thanks, Read More...
Irene November 27, 2018 for Model Number WFG361LVQ2 The oven temperature works erratically . Cooking fine sometimes. Cook 1 pizza, next it will not heat. How do I check sensor and controls?
1 Answer Irene, If you pull the unit out and remove the rear panel, check the oven sensor by disconnecting the connector that has 2 violet or purple wires going into it and test the 2 purple wires for resistance of 1090 ohms at room temp. If the resistance is good then this will likely be a control board issue. Read More...