Mike January 27, 2021 for Model Number MGR5729ADW Maytag MGR5729ADW range, three of the four burners work fine. When the knob is turned for the problem-burner, it does emit gas but does not spark or click (except on very rare occasions) so does not light. None of the other burners spark/click when the problem-burner's knob is turned. Turning any of the other three knobs makes all of the burners spark/click, including the problem-burner. Turning the problem-burner knob so that it is emitting gas and then turning one of the other 3 knobs on will cause the problem-burner to spark and light the gas coming out of it. Seem like just one knob is not sending electricity. What replacement part name & number would correct this problem? Thanks for your help
1 Answer Mike, This issue would most likely be caused by a faulty igniter switch. You can test the switch for continuity in lite position. If there is no continuity then the part is faulty and would need to be replaced. Read More...
Laura March 29, 2019 for Model Number 3468VVV My Maytag stove top burners only click sometimes, mostly I am manually lighting. I have taken everything apart and cleaned them. I believe I need a spark spark ignitor module or harness. Which do you think? If I need the spark igniter harness, does it come complete for all 4 burners as shown in your repair video, or is it a single piece for 34 dollars, able to fix only one burner? Thank you!
1 Answer Laura, you may want to test the spark module [12001596]. With the gas turned off to the stove, you can test the spark module for voltage. If the spark module is receiving 120VAC at the tan wire continuously when a switch is set to the ignite position, it should be sending voltage to the ignitors causing a spark. As it is an intermittent issue, more than likely the spark module is the issue. Read More...
Dicksen December 14, 2016 for Model Number FCG20600B When I turn the knob it suppose all igniter show spark. But only 2 spark and the other 2 is not. One on the right and one on the left spark. so should i replace the ignition switch?
1 Answer Dicksen, This issue would be caused by a spark module that is defective. The part number for the spark module is 12001596. Read More...
Bob November 29, 2016 for Model Number CGR3765ADC One surface burner igniter does not ignite when knob is turned, but the same igniter ignites if any of the other 3 knobs are turned. Do I need to replace the Spark Ignition Switch for just the burner not igniting itself or the whole Spark Module? Thanks
Sam September 05, 2015 for Model Number CBR3765AGC What is difference between part AP4096138 and AP4101554.From your previous email to me you said needed to replace ignighter switch.Which on do I need for my model oven? Also on repair video for this part shows comes with 5 igniters wired together, how does the one for my oven come if I need to replace more than one. Reminding you that this is for igniting stove top burner. Thanks in advance
1 Answer Sam, As far as the differences in the parts, it would appear that where the knob would stop would be different. As for how the part comes, it will come one part per package and the wires will unplug from the original and plug into this part. Read More...
Kerrie August 02, 2015 for Model Number JER8885RCB Need a infinite switch . If I was standing in front of stove, as if I was cooking, its the furthest left dial or the large front burner. Thanks Do you carry the part for my model number^
1 Answer Kerrie, The part number for the infinite switch for the left front burner will be WPW10185286. Read More...
Gil November 07, 2014 I need a spark module part # (ignitor system on the range) for my Maytag MGR5745ADA. Thanks.
Oscar January 02, 2014 for Model Number Admirl 30"stand aone Oven abd stive Oven- while using the oven it stopped working. Purchased a new Glow ignitor because see no glow, Nothing -- changed the contoller before Burner and the Valve and contol for the oven and the Thermo. Still the Oven does not ignite. IS THERE Another COntrol Point the would not allow the Oven to Work?
1 Answer Hello Oscar. We will need your model number to help you with this. Please call 1-877-477-7278 or post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
1 Answer Hello George, Remove the knobs and the screws holding the control panel on the unit. There will be three or four screws under the control panel that you can see when you open the door and look up. The screws located under the knobs will have to be removed also. Some models have a screw or two on the end of the control panel. When you remove the control panel, the switches are easily accessible. Read More...
Bob L December 30, 2012 for Model Number Magic Chef gas range model 7458xta The right front burner will not lite when the knob is turned to lite. I do hear and smell gas but there is no clicking sound that the igniter is working. When I turn any of the other burners to lite and I have the knob for the right front burner in the hi position, the right front burner lites (I know when the igniter is energized, it sparks at all 4 burners). I thnk the igniter switch for this burner is bad. What do you think?
1 Answer Hello Bob, Yes this would be a bad ignitor switch on the Right front burner WP7403P279-60. Read More...