1 Answer Hello Pailboon. The model number you provided is not working. We will need your model number to help you with this. Please post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Dawn M. July 12, 2012 for Model Number GHW9100LW Is this the correct pressure switch for this model, GHW9100LW?
1 Answer Hello Dawn! Yes, the pressure switch WPW10514214 is the correct replacement switched used on Whirlpool GHW9100LW* models. Thanks! Read More...
Jim June 10, 2012 for Model Number WFW9400SW02 The washer was showing an F32 code, Pressure switch, check the harness (checked good) the tech sheet says check pressure switch what contacts? Went ahead and changed pressure switch after clearing hose. Unit still shows F32 in dianostic test, but the washer runs now. How do you clear the codes?
1 Answer Hello Jim. Unplug the unit for about 20 to 25 minutes to reset the unit and clear the codes. Read More...
Steph June 05, 2012 for Model Number WFW9600TW01 My washer keeps saying sud then F35. I checked the line to the pressure switch and blew on it. I also cleared the drain (there was a sock and some money in it). It didn't fix the problem. My washer wasn't empty when I blew on the hose. Would that make a difference or not? If not, do you think it's the pressure switch?
1 Answer Hello Steph. The washer needs to be empty before blowing through the hose. If it is empty and you blow through the hose and it still gives the error, you will need to replace the water level switch WPW10514214 in the unit. Read More...
Christine N. April 17, 2012 for Model Number mfw9600sq0 maytag I just bought this water level pressure switch because I have had the "FH" code blinking after only 2 or 3 minutes into the cycle..My question is after I installed this did I need to disconnect anything to reset or not? I am still getting the FH code?
1 Answer Hello Christine. You may have a bad water valve WP8182862 on the washer and it will need to be replaced. ¦ If there is no water in the unit: —Make sure that both valves at the water source(s) are turned on all the way. —Check for plugged or kinked inlet hoses or plugged screens in the inlet valves. —Verify inlet valve operation. ¦ If there is water in the unit: —Verify drain pump operation. —Verify that the pressure switch hose is in good condition and properly connected to tub and pressure switch. 1. Verify there is not a siphon problem. 2. Unplug washer or disconnect power. 3. Verify wire harness connections to inlet valves, pressure switch, drain pump, flow meter, and Central Control Unit (CCU). 4. Check all hoses for possible leaks. 5. Plug in washer or reconnect power 6. Verify pressure switch operation. 7. Verify flow meter operation by blowing air through the part and measuring the resistance. Hope this helps. Read More...
Jennifer January 09, 2012 for Model Number GHW9100LW I start my washer and it fills with water, but the water never stops coming in? Then It proceeds to shut off and gives me the F/H code. Is this the pressure switch that is bad?
1 Answer Hello Jennifer. Make sure the water is not siphoning out of the unit. If not, then it sounds like the water level switch WPW10514214 is bad and will need to be replaced. Hope this helps. Read More...
Nate B. December 07, 2011 for Model Number Whirlpool WFW9600TW I am getting an F20 error more frequently, I have checked the water lines/screens and even replaced the lines a couple times. This error usually flashes after the wash cycle sometime, now it's happening more frequently. Thank you! Nate
1 Answer Hello Nate. If the water is coming into the machine good and strong on both cold and hot cycles, and the drain hose is not siphoning out the water, you will need to replace the pressure switch WPW10514214. Hope this helps. Read More...
Allen D. December 05, 2011 for Model Number wfw9050xw00 Is this the correct pressure switch for my model number?
1 Answer Hello Allen. No, based on the model number you provided, W11417623 is the correct pressure switch. Hope this helps. Read More...
Loretta December 03, 2011 for Model Number GHW9150PW4 What would make my machine dump water out of the detergent drawer all over the place. I have cleaned the detergent drawer and underneath it. It dumps the water continuously thru the basement the whole time it's running.
1 Answer Loretta, Are you sure the leak is from the dispenser ? The water is injected into the dispenser for a limitted time during the wash cycle, if your wwasher leaks during the whole cycle, you have another issue. Since you've checked and clean the dispenser cups drawer and housing, you will need to remove the top of the washer(three screws across the back of the top panel and slide the top back, disconnect the flex hose from the dispenser and the front of the outer tub and check the hose for a clog or a blockage, and check the opening in the tub as well. For some reason the cardboard caps from bottles have a tendency to fall into the dispenser and get stuck. Thanks and Good Luck Read More...
Zandro November 30, 2011 for Model Number GHW9400PL0 I bought my washer last May 2007 but installed only last Nov 23 '11, the problem is the FH code, stop after washing...I blew the pressure hose and tested again, same problem ...I replaced the pressure switch, same problem the code and stop cycling. Any immidiate sulotion to this prolem Sir/Madam?
1 Answer Hello Zando. Based on the error code, you will need to replace the water valve WP8181694 and make sure the screens in the fill hoses are clear. Hope this helps. Read More...