Gary February 03, 2021 for Model Number 665.13973K017 Does tine-roll WHW10082821 come as a pair or is it just a single tine-roll in the package?
1 Answer Gary, This tine row will come as a single row in one package and if you need a set you will need to order 2 of them. Read More...
Terri Durossette March 15, 2019 for Model Number KUDE03FTSS1 We need to replace the rusted out tine rows. Do they come with the locking tabs and retaining brackets, or are those separately. Just want to make sure we order all parts necessary. What part numbers do you suggest? Thank you for your assistance.
1 Answer Terri, The rack tines and components are separate components, you didn't specify which rack tines you needed. Upper Rack - WPW10082853 / W10082853 Clip, Pivot, WP8539102 / 8539102 Positioner, Dual, W10727426 / 8562030 Tine Row. Lower Rack - W10728160 / W10056272 Tine, Row, WP8531314 / 8531314 Retainer, Tine Row, WPW10078215 / W10078215 Retainer, Tine Row (Combo), WPW10078227 / W10078227 Pivot, Tine Row. Thanks, Read More...
M Nelson December 31, 2017 for Model Number 66513129K702 The dishracks are showing pretty severe damage on certain wires especially protruding ends. Looks electrolytic in nature. Completely corroded thru the end of the collapsible tine-row on the upper rack. You have the part, but 1) should I replace the whole rack, and 2) seems like this is likely to happen again--what's causing it? Thanks for your help.
1 Answer M. Nelson, The tine row will be part number W10728160. If the entire rack is rusting then it would be recommended to replace the entire rack. Make sure that you are not prerinsing dishes and not using too much detergent for your water hardness. Read More...
Craig August 27, 2017 for Model Number KUDT03STSS3 how many tines come in a package? The picture shows 2 rows
1 Answer Craig, kit part number W10727426 comes as set and will include to tine rows. Thanks! Read More...
David August 16, 2017 for Model Number KUDS01DLWH1 Ordered this tine row to replace rusted on in a 15 year old Kitchen Aid. Tines are in locations that do not allow all three clips to fit - any suggestions? The clips also do not fit on the ends as the tines are too close together for the clip. Thanks,
1 Answer David, The tine row on this unit should go from the front of the rack to the back and should have enough room for 3 clips. Make sure that you got the correct tine row and did not need the rear or front tine row which would be different parts. Read More...
Gw March 20, 2017 for Model Number KUDS50SVSS2 I have dishwasher model kuds50svss2 and need to replace some tine rows on the top and bottom racks that have rusted out. In your experience, do I need to replace the entire rack or just the tine rows? Thanks.
1 Answer Hello GW, If the tine rows are stationary and made into the rack, it is best to replace the rack and not just the tine row. If the tine rows are removable and replaceable, then you can replace just the tine rows. Read More...
Bob December 26, 2016 for Model Number 665.17482300 Is tine row WP9744565 one piece? Bottom rod of the original in my dishwasher is 2 pieces glommed together with some kind of flexible goop and then everything painted. So the 2 pieces (one group of 7 tines, other of 9) rotate with respect to each other. Joint has ripped and the pieces are corroded underneath. Thank you.
1 Answer Bob, Yes this is a one piece tine and is held in by 3 pivots which would be part number WP8539189. Read More...
Bs December 02, 2016 for Model Number KUDA03CTBL3 Hi my dishwasher model is KUDA03CTBL3 and I need to replace the tine rows that rusted away. I need one for upper rack and two for lower rack. what are the proper models. I think a may not need the clips, but I am not sure. I cant figure out if the clips would need anything else that would hold it in place. thank you
1 Answer BS, Based on the model number you supplied here is a list of the parts and possible parts you may need to repair the tines on the dishwasher racks. Top rack : W10728160 tine row, WPW10082853 Tine Clip (qty 2). Lower rack : W10727426 Tine Row, WP8531314 Tine retainer(qty 2) , WPW10078227 Pivot(qty 2) , WPW10078215 Retainer (qty 2) Thanks, Read More...
Lynn J. October 14, 2016 for Model Number KUDU03FTPA2 I have the tine rows, tine clips but what do I need to keep the rows in place? It's not clear from the diagram.
1 Answer Hello Lynn, The tine clips "clip" onto the rack and hold the tine rows in place. The "no flip clip" locks the tine row in position. Read More...