Bill March 06, 2013 for Model Number MAV 2757AWW Water is leaking into the tub from the rear rim of the washer. Fills up in a few hours.
1 Answer Hello Bill. If the water valve is leaking water into the tub through the flume assembly, you will need to order and replace the water valve WP21001932 on the unit. Read More...
Kay July 10, 2012 for Model Number PAVT92OAWW MAYTAG (PERFORMA) 3yrs old The washer will not cut off when filling up with water to wash, overflows onto floor. THANK YOU
1 Answer Hello Kay. If you can stop the water by turning the machine off, you will need to replace the pressure switch WPY2201474 or the pressure hose on the unit. If you have to turn off the water to stop the water flow, you will need to order and replace the water valve WP21001932 on the unit. Read More...
1 Answer Hello Mickey. Try filling up the washer on a different water temperature. If it will fill on hot, and not on cold, You will need to replace the water valve WP21001932. If it does not fill on either, you may have a bad lid switch 12001187 or pressure switch 21001882. Hope this helps. Read More...
Johnny B. July 21, 2011 for Model Number HAV2558AWW WASHER WHEN ON WASH, WATER DONT ENTER BUT WHEN I PUT IT ON SPIN IT SPINS OK. WHEN I ROTATE THE KNOB IT WOULD NOT DO NOTHING.
1 Answer Hi Johnny. If you washer will not fill (espically) on both hot or cold, then do you hear them humming when called for a water fill? If so then you will need to replace the water valve. Part # is WP21001932. Thank you. Read More...
Mitterando July 13, 2011 for Model Number nav5805aww When spinning, the washer is always out of balance.
1 Answer Hello Mitterando. You will need to look for plastic shavings in the bottom of the machine. If there are some, the snubber ring WP21002026 will need to be replaced to balance the machine. Hope this helps. Read More...
John July 08, 2011 for Model Number PAV2300AWW When filling the washer, hot works great but cold only comes out a trickle. I've checked both end of filler hose nothing on the filter. Could it be the water inlet valve assembly? What else could it be?
1 Answer Hello John! If the fill hoses are not kinked or clogged it seems that the cold water inlet side of the valve is becoming defective. The inlet valve will need to be replaced. We will need your appliance serial number to verify the correct inlet valve used on your appliance. Thanks! Read More...
Peter A. June 30, 2011 for Model Number PAV2300AWW When washer is not running, water is dripping into the tub from just above the top at the rear. It appears to be dripping from a plastic piece at this location.
1 Answer Hello Peter. It sounds like the water valve is bad and will need to be replaced. You will need to supply your serial number so we can see which valve your washer needs. Hope this helps. Read More...
Tom March 31, 2011 for Model Number pav3300aww maytag washing machine When the washer is filling, the water goes out through the pump as fast as it is filling
1 Answer Hello Tom. You will need to raise the drain hose above the tub of the machine. Also check and make sure there is an air gap where the drian hose enters the drain pipe. Hope this helps. Read More...
Mike February 23, 2011 after I wash clothes the water is coming back.. Not alot of water but clothes are wet... when the washer is off the water is coming in just a little bit.. Have cover off and can see where water is coming from.. What do I need to replace... Is it part number AP4024482 or some other part..
1 Answer If you disconnect the washer from the power outlet and you continue to get water flowing in. The valve is 100% defective and you will need to replace it. If the water is not getting completly drained out then you have to re arrange your drain hose to allow proper drainage. The top of the standpipe must be at least 39" (99 cm) high and no higher than 96" (244 cm) from the bottom of the washer. To avoid siphoning, no more than 8" (20.3 cm) of drain hose should be inside the standpipe. Secure drain hose with beaded tie strap. Read More...
1 Answer This is the water valve that allows the water in the unit. The part that detects the fill of the water and tells the valve to shut off is the water level pressure switch 21001882. Read More...