Parts for Frigidaire CAWE11ERR410A10: 03 - Recommended Spare Parts

This air filter screens the air moving through your appliance's ventilation system, capturing odors and fine particles. Replacing a clogged or damaged filter helps maintain proper airflow so the unit vents and circulates air as designed. What it does:

• Captures odors and airborne particles as air passes through the unit
• Helps maintain proper airflow/venting performance
• Reduces debris buildup on internal components
• Common signs it's due: persistent odors, reduced airflow/venting, a visibly dirty or damaged filter

• 1 air filter

• Disconnect power and allow hot surfaces to cool before servicing
• Open the filter access panel or grille and note the filter's orientation
• Remove the old filter; seat the new filter fully and close the cover
• Restore power and verify proper airflow

This blower wheel circulates air through the dryer drum and venting system to maintain proper airflow for efficient drying. Replaces a worn or damaged wheel to help restore drying performance and reduce unusual noises. What it does:

• Channels air from the dryer motor through the drum and exhaust system
• Helps maintain consistent drum airflow for faster, more even drying
• Can reduce or stop rattling, scraping, or thumping noises caused by a broken or imbalanced wheel
• Restores proper vent pressure that can prevent extended dry cycles

• Disconnect power to the appliance before beginning any repair.
• Access usually requires removing the dryer front or rear panel; keep fasteners organized.
• Inspect the motor shaft, mounting clip, and housing for wear; replace damaged hardware as needed.

This fastener kit supplies the assorted screws and clips used to secure panels and components on compatible Frigidaire appliances, helping restore proper fit and stop loose or rattling parts. Ideal for repairs where original mounting hardware is missing or damaged. What it does:

• Replaces worn, missing or damaged mounting hardware so panels, brackets and trim stay secure
• Helps eliminate vibration noise and loose-fitting parts that cause rattling
• Restores correct alignment for doors, panels or internal assemblies that use small fasteners
• Provides the specific fasteners needed for the factory-replacement process

• Basic hand tools (screwdrivers, nut drivers) are typically required; refer to your model's service manual for exact fastener locations and torque
• Turn off power and disconnect the appliance before starting any repair to avoid shock or injury
• Handle small parts carefully and keep them away from children and pets

This evaporator is the sealed coil inside the freezer compartment that absorbs heat from the cabinet so the refrigerator can maintain proper temperatures. Replacing a damaged or corroded evaporator restores normal cooling performance. What it does:

• Circulates refrigerant through the freezer to absorb heat and enable the cooling cycle
• Removes heat so the compressor and condenser can reject it outside the cabinet
• Commonly associated with symptoms like poor cooling, warm freezer/fridge, or excessive frost/ice buildup on the evaporator
• A damaged or leaking evaporator can lead to long run times or cycling issues

• Disconnect power to the appliance before starting any repair
• Access typically requires removing interior panels and the evaporator cover
• Evaporator is part of the sealed refrigeration system—if the system is leaking or requires brazing
• Avoid puncturing the coil or bending fins; use OEM mounting hardware and replace gaskets as needed

A replacement motor start/run capacitor that helps the refrigerator's compressor and fan motors start and run more reliably. Restores proper motor operation when the original capacitor has failed or weakened. What it does:

• Provides the boost of electrical charge motors need to start and maintain proper running speed
• Commonly linked to symptoms such as a humming compressor, motors that won't start, or intermittent cooling
• Helps stabilize motor performance and reduce hard-starting that can strain components
• Used in refrigeration motor circuits that require a start/run capacitor

• One motor start/run capacitor

• Disconnect power to the appliance before beginning any service
• Capacitors can hold a charge—discharge safely
• Inspect mounting and wiring; replace using the same terminal connections and secure mounting

This oven temperature sensor detects the internal temperature and sends readings to the range control so the oven can maintain accurate cooking temperatures. Replaces a failed or intermittent sensor to restore reliable temperature control. What it does:

• Senses oven cavity temperature and provides temperature data to the control board
• Helps the control maintain set bake/roast temperatures
• Common symptom: oven temperature is incorrect or fluctuates during cooking
• Common symptom: cook cycles take too long or oven does not reach set temperature
• Common symptom: oven displays a temperature sensor or sensor fault code

• One oven temperature sensor (1 each)

• Disconnect electrical power to the appliance before removing or installing the sensor
• Handle the sensor carefully to avoid damaging the probe or wiring and ensure proper connector seating
• Inspect wiring and connector for damage; replace if frayed or corroded

This replacement power cord restores AC power to compatible refrigerators by replacing a damaged or worn supply lead. It provides a direct, safe power connection so the appliance can run reliably. What it does:

• Replaces a frayed, cut, or otherwise damaged power supply cord
• Restores consistent power when the appliance will not turn on or has intermittent power
• Maintains the appliance's grounding connection for safe operation
• Prevents electrical arcing from exposed wiring or compromised insulation

• One replacement power cord

• Disconnect the appliance from the power source before inspecting or replacing the cord
• Install with the proper strain relief and secure fasteners to prevent pinching or pull-out