Parts for Frigidaire CRA144HT211: 03 - Recommended Spare Parts

This air filter screens the air moving through your appliance's ventilation system, capturing odors and fine particles. Replacing a clogged or damaged filter helps maintain proper airflow so the unit vents and circulates air as designed. What it does:

• Captures odors and airborne particles as air passes through the unit
• Helps maintain proper airflow/venting performance
• Reduces debris buildup on internal components
• Common signs it's due: persistent odors, reduced airflow/venting, a visibly dirty or damaged filter

• 1 air filter

• Disconnect power and allow hot surfaces to cool before servicing
• Open the filter access panel or grille and note the filter's orientation
• Remove the old filter; seat the new filter fully and close the cover
• Restore power and verify proper airflow

This blower wheel circulates air through the dryer drum and venting system to maintain proper airflow for efficient drying. Replaces a worn or damaged wheel to help restore drying performance and reduce unusual noises. What it does:

• Channels air from the dryer motor through the drum and exhaust system
• Helps maintain consistent drum airflow for faster, more even drying
• Can reduce or stop rattling, scraping, or thumping noises caused by a broken or imbalanced wheel
• Restores proper vent pressure that can prevent extended dry cycles

• Disconnect power to the appliance before beginning any repair.
• Access usually requires removing the dryer front or rear panel; keep fasteners organized.
• Inspect the motor shaft, mounting clip, and housing for wear; replace damaged hardware as needed.

This dryer drive motor powers the drum and blower so clothes tumble and air circulates for effective drying. Replaces a worn or noisy motor to restore normal drum rotation and airflow. What it does:

• Spins the dryer drum so clothes tumble during the cycle
• Powers the blower wheel to move air through the drum and vent
• Stops abnormal noise or shaking caused by a failing motor
• Helps eliminate no-rotation or intermittent-rotation symptoms

• One dryer drive motor assembly

• Disconnect power before servicing to avoid shock or injury
• Verify motor orientation and blower-wheel seating before final assembly
• Inspect and replace worn belts or idler pulleys while unit is open

This fastener kit supplies the assorted screws and clips used to secure panels and components on compatible Frigidaire appliances, helping restore proper fit and stop loose or rattling parts. Ideal for repairs where original mounting hardware is missing or damaged. What it does:

• Replaces worn, missing or damaged mounting hardware so panels, brackets and trim stay secure
• Helps eliminate vibration noise and loose-fitting parts that cause rattling
• Restores correct alignment for doors, panels or internal assemblies that use small fasteners
• Provides the specific fasteners needed for the factory-replacement process

• Basic hand tools (screwdrivers, nut drivers) are typically required; refer to your model's service manual for exact fastener locations and torque
• Turn off power and disconnect the appliance before starting any repair to avoid shock or injury
• Handle small parts carefully and keep them away from children and pets

This run capacitor helps the refrigerator's motor start and run more reliably, reducing strain on the compressor and fan. Replacing a failing capacitor can restore normal motor operation and help the appliance cool properly. What it does:

• Provides the electrical phase shift needed for motor start and continuous operation
• Helps reduce motor overheating and hard-start symptoms
• Commonly replaced when motors hum, won't start, or cycle erratically
• Supports steady compressor and fan performance for consistent cooling

• One run capacitor (single unit as pictured)

• Disconnect power to the appliance before inspecting or replacing the capacitor
• Discharge the capacitor safely before handling to avoid shock
• Verify terminal markings and wiring; replace with same type and ratings

This oven temperature sensor detects the internal temperature and sends readings to the range control so the oven can maintain accurate cooking temperatures. Replaces a failed or intermittent sensor to restore reliable temperature control. What it does:

• Senses oven cavity temperature and provides temperature data to the control board
• Helps the control maintain set bake/roast temperatures
• Common symptom: oven temperature is incorrect or fluctuates during cooking
• Common symptom: cook cycles take too long or oven does not reach set temperature
• Common symptom: oven displays a temperature sensor or sensor fault code

• One oven temperature sensor (1 each)

• Disconnect electrical power to the appliance before removing or installing the sensor
• Handle the sensor carefully to avoid damaging the probe or wiring and ensure proper connector seating
• Inspect wiring and connector for damage; replace if frayed or corroded

A handheld replacement remote that restores convenient, wireless control of your appliance's basic functions — power, mode, temperature and fan settings — without needing to access the control panel directly. What it does:

• Sends wireless commands to the appliance to change power, temperature, fan speed and operating mode
• Replaces a lost, damaged or non-working remote to restore remote operation
• Helps diagnose remote-related control issues by providing a working transmitter for testing
• Works with the appliance's front-panel receiver; operation depends on line-of-sight and fresh batteries

• Install fresh batteries before first use and follow the appliance manual to pair or sync if required
• Point remote at the appliance's IR/receiver window and test functions at close range first
• Keep remote dry and avoid dropping; handle electronic parts with care
• Dispose of batteries and packaging according to local regulations