Parts for Crosley CAHE8ERR410A14: Recommended Spare Parts

This factory air filter helps keep your appliance's ventilation system clean and unrestricted. Replacing a dirty or damaged filter supports proper airflow, protects internal components, and helps reduce unwanted odors during normal operation.

• Screens airborne debris along the intake/exhaust path to protect internal parts
• Helps maintain consistent airflow for effective ventilation
• Replace when clogged, torn, warped, or missing
• Common signs include weak ventilation, lingering odors, or a visibly dirty/damaged filter

• Disconnect power before servicing
• Access the filter location per your model (grille, vent panel, or access cover)
• Note orientation and fully seat the new filter; secure any tabs or screws as designed
• Do not operate the appliance without the filter installed

This replacement door frame restores the outer support and trim around an appliance door, helping the door seal properly and maintain correct alignment for safe, efficient operation. Fits original equipment design. What it does

• Provides structural support for the appliance door and secures outer trim pieces.
• Helps maintain proper door alignment so the door closes evenly and seals.
• Replaces cracked, bent or damaged frames that cause gaps, rattling or misalignment.
• Restores the appearance of the appliance exterior when the original frame is dented or worn.

• Disconnect power to the appliance before starting any repair to avoid shock or injury.
• Handle any attached glass, trim or clips carefully to avoid breakage or cuts.
• Basic hand tools are typically required; installation may require removing the door or outer panels.

This replacement wire provides a single insulated conductor used to reconnect or repair electrical connections inside the appliance, restoring reliable signal or power flow to the affected component. What it does

• Re-establishes an electrical connection between components when an original wire is damaged or disconnected
• Helps resolve symptoms such as intermittent operation, no power to a circuit, or a loose connection in the appliance
• Prevents arcing and poor contact when a worn or frayed wire is replaced
• Used as a direct inline conductor where the OEM wiring is faulty

• One replacement insulated wire

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Match wire routing and terminal orientation to the original; secure with existing clips or ties to prevent chafing
• Ensure proper connector seating and no exposed conductor is left exposed after installation
• If multiple wires or a full harness are damaged, replace the entire harness per manufacturer guidance

This replacement evaporator fan blade circulates cold air across the freezer and refrigerator compartments to help maintain even temperatures and efficient cooling. Designed to match the OEM shape for proper airflow and fit. What it does:

• Spins on the evaporator fan motor to move cold air through the evaporator and into the cabinet
• Helps stabilize internal temperatures and reduce frost buildup when operating correctly
• Commonly replaced when cracked, chipped, warped, or causing unusual noise or poor airflow
• Restores proper airflow to improve cooling performance when the original blade is damaged

• One fan blade

• Disconnect power before servicing the appliance to avoid electrical shock or injury
• Inspect the motor shaft and mounting for damage; clean debris before installing the new blade
• Ensure the blade is seated fully and rotates freely without rubbing against the housing
• If the motor shows excessive wear or noise, replace the motor assembly as needed rather than just the blade

This replacement rail is a single pull-out drawer slide that restores smooth movement and proper alignment for refrigerator drawers and bins. It helps stop sticking, slipping, or uneven drawer travel so trays open and close reliably. What it does

• Replaces a worn or damaged drawer slide to restore smooth, even drawer movement.
• Supports proper alignment and prevents drawers from binding or falling off their tracks.
• Commonly used when drawers feel loose, catch, or do not fully extend or retract.
• Fits as a single rail—use with the matching opposite side if replacing both rails.

• One rail (drawer slide), sold individually.

• High-level: remove the drawer or bin to access the rail; compare orientation before removing old part.
• Use basic hand tools; keep screws and fasteners for reassembly if the new rail does not include them.
• For safety, unplug or disconnect power to the appliance if working near electrical components.

The Thermistor is an OEM replacement part for Frigidaire room air conditioners. Located within the air conditioner unit, the thermistor accurately monitors and regulates the equipment's internal air temperature. Precisely calibrated at the factory, the thermistor allows the unit to continuously achieve and maintain the preset cooling level preferred by the user. 

Symptoms of a bad thermistor include:  

• Inconsistent or fluctuating room temperatures
• Difficulty reaching or maintaining desired temperatures  
• The control panel shows abnormal temperature readings

Causes can be age-related deterioration of sensing components, moisture exposure damaging circuitry, or loose wiring connections preventing exact temperature measurement over time. This OEM thermistor restores precise temperature control.

Replacing a faulty thermistor prevents improper compressor cycling which wastes energy. Compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This oven temperature sensor detects the internal temperature and sends readings to the range control so the oven can maintain accurate cooking temperatures. Replaces a failed or intermittent sensor to restore reliable temperature control. What it does:

• Senses oven cavity temperature and provides temperature data to the control board
• Helps the control maintain set bake/roast temperatures
• Common symptom: oven temperature is incorrect or fluctuates during cooking
• Common symptom: cook cycles take too long or oven does not reach set temperature
• Common symptom: oven displays a temperature sensor or sensor fault code

• One oven temperature sensor (1 each)

• Disconnect electrical power to the appliance before removing or installing the sensor
• Handle the sensor carefully to avoid damaging the probe or wiring and ensure proper connector seating
• Inspect wiring and connector for damage; replace if frayed or corroded