Parts for Electrolux FFRE25L3S20: 02 - Recommended Spare Parts

This refrigerator water filter removes common impurities from the ice and water supply so you get cleaner-tasting water and clearer ice. Designed to fit inline/replaceable filter housings used in many Frigidaire refrigerators. What it does:

• Reduces chlorine taste and odor for improved drinking water flavor
• Helps reduce sediment and particulates that can affect ice clarity
• Keeps water flowing properly when replaced as part of routine maintenance
• Addresses symptoms like cloudy ice, bad-tasting water, or reduced water quality

• One replacement refrigerator water filter cartridge

• Replace filter according to your refrigerator manufacturer's instructions; typically twist or push in to seat and lock
• Run several gallons of water through the dispenser after installation to flush the system and remove loose carbon fines
• If water flow is restricted after installation, check filter orientation and seating; do not force
• For safety, disconnect power to the appliance before accessing internal filter housings

This frame is the exact replacement trim piece that restores the appliance's front appearance and supports adjacent panels. Replacing a damaged or bent frame improves fit and helps keep internal parts protected from debris. What it does:

• Provides structural support and alignment for the appliance front panels
• Covers and protects edges where panels meet to prevent dirt and moisture intrusion
• Restores cosmetic appearance if the original frame is scratched, dented, or warped
• Helps maintain proper door or control-panel fit when worn or bent

• One replacement frame

• Disconnect power to the appliance before starting any repair
• Installation typically requires removing adjoining trim or screws; retain fasteners for reuse
• Use hand tools and avoid over-tightening to prevent cracking the new frame

Electronic control board that manages a refrigerator's cooling, defrost and user-interface functions, restoring responsive controls and proper cycling when a failed system control causes erratic operation. What it does

• Regulates compressor, fans and relay switching to manage cooling cycles — failure can cause warm interior or continuous running.
• Controls defrost timing and heater operation to prevent frost buildup and excessive ice.
• Powers and communicates with the display and user controls — faults can cause blank or unresponsive controls.
• Monitors sensor inputs and coordinates system responses to maintain set temperatures.

• Disconnect power to the appliance before servicing to avoid shock or equipment damage.
• Handle the board by its edges and avoid static discharge — use anti-static precautions if available.
• Secure all connectors and mounting hardware, then power up and confirm normal operation and proper temperature cycling.

This replacement wire provides a single insulated conductor used to reconnect or repair electrical connections inside the appliance, restoring reliable signal or power flow to the affected component. What it does

• Re-establishes an electrical connection between components when an original wire is damaged or disconnected
• Helps resolve symptoms such as intermittent operation, no power to a circuit, or a loose connection in the appliance
• Prevents arcing and poor contact when a worn or frayed wire is replaced
• Used as a direct inline conductor where the OEM wiring is faulty

• One replacement insulated wire

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Match wire routing and terminal orientation to the original; secure with existing clips or ties to prevent chafing
• Ensure proper connector seating and no exposed conductor is left exposed after installation
• If multiple wires or a full harness are damaged, replace the entire harness per manufacturer guidance

This refrigerator door handle provides a stable grip for opening and closing the door and restores the door's original appearance and function. Designed as a direct-fit replacement where this OEM-style handle is specified. What it does

• Replaces a damaged, cracked, or loose refrigerator door handle to restore safe, reliable opening and closing.
• Provides a secure grip and proper alignment for the door during normal use.
• Helps prevent further wear to the door edge and surrounding trim by restoring correct handle function.
• Compatible with factory handle mounting points when the OEM part number matches.

• One refrigerator door handle

• Installation typically requires removing the old handle screws or clips and securing the replacement in the same mounting locations.
• Use appropriate hand tools; avoid overtightening fasteners which can crack the handle or strip threads.
• Keep the door supported during removal/installation to avoid hinge or door damage.
• Turn off power to any nearby components (ice maker lights, etc.) before working.

Handheld remote control that restores convenient, wireless operation of your Frigidaire appliance. Use it to send commands for functions, settings and timers when the original remote is lost or no longer responding. What it does:

• Sends infrared/remote commands to the appliance so you can change settings from a distance.
• Lets you start, stop or adjust modes and timers without using the appliance control panel.
• Replaces a lost, cracked or unresponsive original remote to restore remote operation.
• Requires pairing/programming with the appliance per the owner's manual.

• Remove power or unplug the appliance before accessing internal components; handle electronics carefully.
• Use fresh batteries and insert them following polarity markings; follow local rules for battery disposal.

This replacement power cord restores electrical supply to your appliance so it can run safely and reliably. Designed to match the original cord's fit and function for straightforward replacement. What it does:

• Provides the main AC connection to restore power when the cord is damaged or fails
• Replaces cords with cracked insulation, exposed wiring, or loose connections
• Helps stop intermittent power, arcing, or loss of power caused by a faulty cord
• Matches original wiring configuration for proper fit and connection

• Turn off power at the breaker and unplug the appliance before servicing.
• Use proper tools and secure all wire terminals; avoid pinching or crushing the cord.

The Thermistor is an OEM replacement part for Frigidaire room air conditioners. Located within the air conditioner unit, the thermistor accurately monitors and regulates the equipment's internal air temperature. Precisely calibrated at the factory, the thermistor allows the unit to continuously achieve and maintain the preset cooling level preferred by the user. 

Symptoms of a bad thermistor include:  

• Inconsistent or fluctuating room temperatures
• Difficulty reaching or maintaining desired temperatures  
• The control panel shows abnormal temperature readings

Causes can be age-related deterioration of sensing components, moisture exposure damaging circuitry, or loose wiring connections preventing exact temperature measurement over time. This OEM thermistor restores precise temperature control.

Replacing a faulty thermistor prevents improper compressor cycling which wastes energy. Compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This oven temperature sensor detects the internal temperature and sends readings to the range control so the oven can maintain accurate cooking temperatures. Replaces a failed or intermittent sensor to restore reliable temperature control. What it does:

• Senses oven cavity temperature and provides temperature data to the control board
• Helps the control maintain set bake/roast temperatures
• Common symptom: oven temperature is incorrect or fluctuates during cooking
• Common symptom: cook cycles take too long or oven does not reach set temperature
• Common symptom: oven displays a temperature sensor or sensor fault code

• One oven temperature sensor (1 each)

• Disconnect electrical power to the appliance before removing or installing the sensor
• Handle the sensor carefully to avoid damaging the probe or wiring and ensure proper connector seating
• Inspect wiring and connector for damage; replace if frayed or corroded

This replacement capacitor stores and releases electrical energy to support proper operation of the appliance's circuit. Replacing a weakened or failed capacitor restores reliable startup and smooth performance in the affected component.

• Stores electrical energy and delivers a brief boost during startup as designed by the circuit
• Helps stabilize operation, reducing humming, stalling, or overheating from a weak capacitor
• Common signs include motors that hum but won't start, intermittent operation, breaker trips
• Visual clues of failure: swollen case, leaking oil, or burnt odor

• Disconnect power and verify no voltage is present before servicing
• Properly discharge the old capacitor using safe, approved procedures
• Note wire positions or take a photo; transfer leads to the matching terminals securely
• Mount securely in the existing bracket/strap; keep terminals clear of contact and test operation

This start/run capacitor helps provide the extra electrical push motors need to start and run smoothly, restoring reliable operation to the motor circuit and reducing hard-start symptoms. What it does:

• Provides temporary stored electrical energy to help the motor start and maintain stable operation
• Commonly used in motor circuits for compressors, fans or drive motors depending on application
• Resolves symptoms such as humming, motors that won't start, slow or intermittent motor operation
• Supports consistent motor torque and can improve overall system reliability when failed capacitors cause performance loss

• Disconnect power to the appliance before servicing to avoid shock hazard
• Capacitors can hold a charge; discharge safely
• Verify terminal layout and mounting match the old part before installation

This evaporator coil assembly circulates refrigerant and absorbs heat inside the freezer compartment to enable proper cooling. Replacing a failed evaporator restores the sealed-system heat-exchange surface the appliance needs to maintain low temperatures. What it does

• Absorbs heat from the freezer compartment so refrigerant can carry it away
• Enables frost/defrost cycle to prevent excessive ice buildup when working properly
• Common symptoms indicating failure: excessive frost or ice on the evaporator, poor or uneven cooling, or warm freezer compartment
• Works as part of the sealed refrigeration system alongside the compressor, condenser and expansion device

• Disconnect power to the appliance before starting any repair.
• Defrost and remove ice buildup as needed to access the evaporator; follow OEM service instructions.
• Handle carefully to avoid bending fins or cutting yourself on sharp edges; wear gloves and eye protection.

This replacement water supply tube routes water from the refrigerator's valve to the ice maker or dispenser, restoring proper water flow and preventing leaks when the original tube is cracked or blocked. What it does

• Carries water from the inlet/valve to the ice maker or dispenser assembly.
• Restores normal water flow when a damaged or clogged tube causes slow fill or no fill.
• Helps stop leaks and drips caused by cracks, splits or loose connections.
• Compatible with OEM connections and fittings used on affected Frigidaire refrigerators.

• One replacement water supply tube.

• Turn off the refrigerator and shut off the water supply before starting any work.
• Unplug the appliance to avoid electrical shock when accessing internal components.
• Replace only with the exact part number; secure all fittings to prevent leaks.
• After installation, restore water, check for leaks, and run a test fill to verify correct operation.

This condenser coil assembly helps remove heat from the refrigerant so your refrigerator can cool efficiently. A properly working condenser supports normal cooling and helps prevent the compressor from overworking. What it does:

• Dissipates heat from the refrigerant to allow proper cooling
• Helps maintain normal compressor cycling and appliance temperature
• Can cause reduced cooling or an overworking compressor when damaged or clogged
• Works with the refrigeration system; not an electrical or fan motor component

• One condenser coil assembly

• Disconnect power to the appliance before starting any service
• Handle carefully; fins are sharp and the coil can be bent or damaged
• May require removing the rear access panel or toe grille and repositioning nearby components

This scroll is the replaceable spiral element used inside a refrigeration compressor to compress refrigerant and restore proper cooling performance. It's the OEM-design component that engages with the mating scroll to form the compression chambers. What it does:

• Forms the moving or stationary spiral surface in a scroll-type compressor to compress refrigerant
• Restores internal compression when the factory scroll is damaged or worn
• Can help resolve symptoms such as loss of cooling, excessive compressor noise, or failed compression when diagnosis confirms scroll damage
• Works only as part of a compatible scroll compressor assembly; not a standalone drop-in pump solution

• Replacement requires compressor disassembly and reassembly
• Follow OEM torque, alignment, and sealant procedures; improper installation can cause compressor failure
• Observe all safety precautions for handling pressurized refrigerant and electrical components

This blower wheel moves air through the dryer cabinet so clothes dry efficiently and the appliance vents properly. Replacing a worn or damaged wheel restores airflow and helps prevent overheating and long dry times. What it does:

• Spins on the blower motor shaft to draw air across the heating element and through the drum
• Restores proper airflow when a chipped or bent wheel causes reduced drying performance
• Reduces rattling or vibration caused by imbalanced or cracked fins
• Helps prevent overheating and extended cycle times due to restricted airflow

• One blower wheel

• Disconnect power (and gas if applicable) before servicing to avoid electric shock or injury
• May require removal of the dryer front or blower housing and loosening the motor to slide the wheel onto the shaft
• Ensure the wheel is oriented and seated correctly on the motor shaft and that set screws or clips are tightened as required
• Inspect motor shaft and housing for debris; spin the new wheel by hand to ensure free rotation before reassembly

This replacement blade fan moves cold air across the evaporator to help maintain even temperatures inside the compartment. It restores proper airflow for more consistent cooling and helps reduce frost buildup when working with a good motor. What it does:

• Circulates air across the evaporator to distribute cold air through the compartment
• Restores airflow when a cracked, warped, or missing blade reduces cooling efficiency
• Helps reduce uneven temperatures and localized warm spots caused by poor airflow
• Can reduce abnormal noises caused by damaged or unbalanced blades

• One replacement blade fan

• Disconnect power to the appliance before starting any repair
• Remove the evaporator cover/panel to access the fan assembly per your model's service instructions
• Handle the replacement blade carefully to avoid bending the blades or contaminating the evaporator
• If the fan motor or mounting hardware is damaged, replace those parts as well for reliable operation