Parts for Electrolux FFRH0822R11: 02 - Recommended Spare Parts

This factory air filter helps keep your appliance's ventilation system clean and unrestricted. Replacing a dirty or damaged filter supports proper airflow, protects internal components, and helps reduce unwanted odors during normal operation.

• Screens airborne debris along the intake/exhaust path to protect internal parts
• Helps maintain consistent airflow for effective ventilation
• Replace when clogged, torn, warped, or missing
• Common signs include weak ventilation, lingering odors, or a visibly dirty/damaged filter

• Disconnect power before servicing
• Access the filter location per your model (grille, vent panel, or access cover)
• Note orientation and fully seat the new filter; secure any tabs or screws as designed
• Do not operate the appliance without the filter installed

This replacement wire provides a single insulated conductor used to reconnect or repair electrical connections inside the appliance, restoring reliable signal or power flow to the affected component. What it does

• Re-establishes an electrical connection between components when an original wire is damaged or disconnected
• Helps resolve symptoms such as intermittent operation, no power to a circuit, or a loose connection in the appliance
• Prevents arcing and poor contact when a worn or frayed wire is replaced
• Used as a direct inline conductor where the OEM wiring is faulty

• One replacement insulated wire

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Match wire routing and terminal orientation to the original; secure with existing clips or ties to prevent chafing
• Ensure proper connector seating and no exposed conductor is left exposed after installation
• If multiple wires or a full harness are damaged, replace the entire harness per manufacturer guidance

This defrost drain pan collects and channels water from the refrigerator's defrost cycle to prevent leaks and pooling under the cabinet. It restores proper drain flow and helps keep the area beneath the unit dry. What it does:

• Catches and routes melted frost and defrost water to the drain system or evaporator area
• Prevents water from pooling under the refrigerator that can cause odors or floor damage
• Works with the evaporator and defrost components to maintain normal condensation management
• Commonly replaced when cracked, warped, or leaking during defrost cycles

• One defrost drain pan / evaporator tray

• Turn off power to the appliance before servicing to avoid electrical shock
• Access typically requires removing lower kick plate or internal shelves; follow your model's service instructions
• Inspect surrounding seals, drain tube, and mounting tabs; replace any damaged components to ensure a proper seal

The Thermistor is an OEM replacement part for Frigidaire room air conditioners. Located within the air conditioner unit, the thermistor accurately monitors and regulates the equipment's internal air temperature. Precisely calibrated at the factory, the thermistor allows the unit to continuously achieve and maintain the preset cooling level preferred by the user. 

Symptoms of a bad thermistor include:  

• Inconsistent or fluctuating room temperatures
• Difficulty reaching or maintaining desired temperatures  
• The control panel shows abnormal temperature readings

Causes can be age-related deterioration of sensing components, moisture exposure damaging circuitry, or loose wiring connections preventing exact temperature measurement over time. This OEM thermistor restores precise temperature control.

Replacing a faulty thermistor prevents improper compressor cycling which wastes energy. Compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This oven temperature sensor detects the internal temperature and sends readings to the range control so the oven can maintain accurate cooking temperatures. Replaces a failed or intermittent sensor to restore reliable temperature control. What it does:

• Senses oven cavity temperature and provides temperature data to the control board
• Helps the control maintain set bake/roast temperatures
• Common symptom: oven temperature is incorrect or fluctuates during cooking
• Common symptom: cook cycles take too long or oven does not reach set temperature
• Common symptom: oven displays a temperature sensor or sensor fault code

• One oven temperature sensor (1 each)

• Disconnect electrical power to the appliance before removing or installing the sensor
• Handle the sensor carefully to avoid damaging the probe or wiring and ensure proper connector seating
• Inspect wiring and connector for damage; replace if frayed or corroded

A replacement start/run capacitor that helps the refrigerator's motor(s) get up to speed for reliable cooling and circulation. Restores proper motor starting when the original capacitor has failed. What it does:

• Provides the electrical boost needed for compressor and fan motors to start and run smoothly
• Commonly replaced when motors hum, fail to start, or fridge cooling is inconsistent
• Helps prevent motor overloads and repeated hard-start cycling when functioning correctly
• Matches the original part's role in the appliance's electrical starting circuit

• Disconnect power to the appliance at the breaker before servicing
• Discharge the capacitor before touching terminals to avoid shock; use insulated tools
• Verify terminal orientation and secure wire connections; do not force fit

This replacement rail is a single pull-out drawer slide that restores smooth movement and proper alignment for refrigerator drawers and bins. It helps stop sticking, slipping, or uneven drawer travel so trays open and close reliably. What it does

• Replaces a worn or damaged drawer slide to restore smooth, even drawer movement.
• Supports proper alignment and prevents drawers from binding or falling off their tracks.
• Commonly used when drawers feel loose, catch, or do not fully extend or retract.
• Fits as a single rail—use with the matching opposite side if replacing both rails.

• One rail (drawer slide), sold individually.

• High-level: remove the drawer or bin to access the rail; compare orientation before removing old part.
• Use basic hand tools; keep screws and fasteners for reassembly if the new rail does not include them.
• For safety, unplug or disconnect power to the appliance if working near electrical components.