Parts for Frigidaire FRSS2323AS4: Refrigerator Door Parts

This door gasket seals the perimeter of the appliance door to keep cold air in and humid air out. Replace a torn, warped, or leaky gasket to restore stable temperatures, reduce frost/condensation, and help the unit run efficiently. What it does:

• Creates an airtight seal between the door and cabinet
• Helps maintain proper temperature and humidity inside the compartment
• Reduces frost buildup and condensation around the door opening
• Common failure signs: tears, gaps, warping, hard or cracked rubber, door not closing flush, warm spots

• 1 door gasket

• Unplug the appliance and clear items from the affected door.
• Condition the new gasket to remove shipping kinks by laying it flat and warming it (soak in warm water or use gentle, low heat).
• Remove the old gasket; on some models you may need to loosen liner-retainer screws to release it.
• Fit the new gasket into the channel, working from the corners; ensure it seats evenly all around and verify a uniform seal.

This replacement access panel cover protects internal components and restores the appliance's finished appearance. It keeps wiring and controls enclosed to reduce debris buildup and accidental contact. What it does:

• Covers and protects internal control or wiring areas from dust, spills, and physical damage
• Prevents accidental contact with electrical components for improved safety
• Stops rattling or vibration noises caused by a missing or loose cover
• Restores a clean, finished look to the appliance exterior or interior

• One replacement access panel cover

• Disconnect power (unplug or shut off breaker) before starting any work
• Use basic hand tools to remove fasteners; keep hardware for reuse
• Handle cover carefully to avoid cracking plastic or scratching finished surfaces

The Handle is an OEM component specifically designed for Frigidaire refrigerators. This door handle is located on the exterior front of the fridge, providing an ergonomic grip for easy opening and closing of the refrigerator door. 

Symptoms of a bad handle can include loose mounting, difficulty grasping or turning the handle, or physical damage rendering it unusable. 

Causes of a bad handle include wear and tear over time, damage from impact or harsh cleaning chemicals, or loose fasteners allowing the handle to wobble.

Symptoms of a bad handle include:

• Loose, unstable grip that cannot support door weight  
• Difficulty opening and closing the refrigerator door
• Damage to the handle mechanism, mounting bracket, or appearance

This OEM Frigidaire replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. Replace yours today before replacing becomes necessary.
 

This #10-32 x 3/4-inch machine screw secures appliance components such as panels, brackets, and handles. Using the correct length and thread helps restore a snug, rattle-free hold wherever this screw is specified by the manufacturer.

• Fastens components with a #10-32 machine thread and 3/4-inch length
• Helps keep panels, trim, brackets, or handles secured and aligned
• Replaces missing, stripped, or corroded hardware
• Common signs include loose or wobbly parts, rattling, missing screws, or damaged screw heads/threads

• Disconnect power before servicing; if working near a water connection, shut off the water supply
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten to prevent stripping plastic or threads
• Reuse any model-specific washers or spacers if present

The Screw is an OEM replacement part for Frigidaire refrigerators. This small but essential component is used to secure various parts of the appliance, such as panels, brackets, or internal fixtures, ensuring the refrigerator's structural integrity and proper operation.

Over time, screws may become loose, stripped, or corroded due to regular use, environmental factors, or maintenance work. A damaged or missing screw can lead to misaligned parts or reduced stability of the appliance.

Symptoms of a bad or missing screw include:

• Loose or wobbly components within the refrigerator
• Panels or fixtures coming apart or misaligned
• Difficulty securing parts during maintenance or repair
• Rattling or unusual noises during operation

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This door bushing kit replaces worn hinge bushings that keep refrigerator/freezer doors aligned for smooth, stable operation. Restores proper door rotation to reduce sagging, rubbing, and noisy or stiff hinges. What it does:

• Provides replacement hinge bushings that support the door on its hinge pin for correct alignment
• Helps stop door sag, scraping, and uneven gaps that let cold air escape
• Reduces hinge noise, sticking, and rough door movement
• Fits into the door hinge assembly to restore smooth pivoting action

• Always unplug the appliance or disconnect power before starting repairs
• Support the door while removing hinge pins to prevent dropping or damage
• Remove old bushings from the hinge housing and press or snap new bushings into place; reassemble hinge and confirm alignment

A single replacement screw used to fasten appliance panels and components securely. This genuine-style fastener restores proper fit and helps eliminate rattles or loose parts after service or repairs. What it does:

• Secures panels, brackets, or trim to the appliance frame
• Restores tight, stable mounting to stop rattling or vibration
• Replaces missing or stripped hardware so parts align correctly
• Works where the original appliance screw was used

• Use matching driver and apply moderate torque to avoid stripping the head or threads
• Disconnect power or unplug the appliance when accessing internal areas
• If screw threads are damaged, replace with an identical part rather than forcing

Specs: 10-16 X 0.500

This factory fastener secures appliance panels and components. Replace a missing, stripped, or corroded screw to restore a tight, rattle-free fit and keep brackets and covers properly aligned.

• Fastens panels, brackets, and internal parts as specified by the manufacturer
• Helps maintain alignment and reduces vibration/rattling
• Replace if the head is stripped, threads are damaged, or corrosion is present
• Symptoms include loose/missing hardware, gaps, or rattling during operation

• Disconnect power; shut off gas/water if applicable before servicing
• Use the correct driver/bit size to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Match screw length/thread to the location; replace in sets when required

This bin assembly replaces a damaged or missing storage bin in your refrigerator, restoring secure, organized storage so items stay contained and the compartment functions as designed. What it does:

• Holds and organizes items in the designated location for your model
• Keeps contents contained to help prevent spills or items sliding/falling
• Maximizes usable space and helps maintain an orderly compartment
• Common signs it's needed: cracked plastic, broken mounting tabs, bin won't stay seated or falls off

• 1 bin assembly

• Remove the old bin and any contents; clean the area if needed
• Align the new bin with the model's hooks/slots and press or snap into place—do not force
• Confirm placement matches your model's diagram for a secure fit
• Avoid overloading; distribute weight evenly to prevent future damage

The Door Shelf Bin is an OEM component for Frigidaire refrigerators. Situated inside the refrigerator door, this removable tray provides convenient storage for condiments and other small items.

Causes of a bad door shelf bin can include cracks or fractures from repeated loading/unloading, or wear to mounting brackets compromising secure placement.

Symptoms of a bad door shelf bin include:

• Failure to properly click into mounting rails
• Warped plastic unable to hold contents inside
• Cracks or breaks exposing stored items to spills

Note: Approximately 13” x 8”

Also compatible with Electrolux models, restored functionality and capacity ensure contents are neatly positioned at hand.

This factory screw fastens refrigerator components and panels. It replaces missing or damaged hardware so parts stay aligned and secure, reducing looseness and rattles caused by vibration. What it does:

• Secures panels, brackets, and trim per your model's design
• Helps maintain alignment and reduce vibration-related loosening or noise
• Replaces missing, stripped, or corroded hardware
• Restores a snug fit when threads or heads are worn

• One screw

• Disconnect power; turn off the water supply if working near ice or dispenser systems
• Use the correct driver; start threading by hand to avoid cross-threading
• Tighten until snug—do not overtighten to prevent stripping or cracking adjacent plastic
• Refer to your model's diagram to confirm location and quantity used

This part number contains one (1) screw.

This replacement screw secures appliance components in place. Use it to replace a missing, stripped, or rusted fastener so shelves, handles, panels, or brackets stay properly mounted and the unit operates without unwanted movement.

• Fastens components to the cabinet, door, liner, or frame
• Restores a solid fit when the original screw is worn or lost
• Helps eliminate looseness, rattling, or misalignment
• Matches the original hardware for correct fit and thread engagement

• Disconnect power before servicing; for refrigerators, also turn off the water supply
• Align parts and start the screw by hand to avoid cross-threading
• Tighten with the correct driver; do not overtighten, especially into plastic
• If receiving threads are damaged, repair or replace the mating clip/bracket before installing

This genuine replacement screw restores a secure hold for panels, trim, or internal components. It replaces worn or missing fasteners so parts stay aligned and appliances operate safely. What it does:

• Fastens panels, brackets, or trim into place
• Replaces stripped, missing, or damaged screws
• Helps stop rattling, loose panels, or misaligned trim
• Fits OEM mounting locations that require the specified machine screw

• Use the correct driver to avoid stripping the head
• Hand-start the screw, then tighten to firm snug; do not over-torque
• Disconnect power to the appliance before accessing internal components
• If other fasteners are damaged, inspect and replace as needed

This refrigerator clip is a small retainer that secures a component in place so it stays properly seated during use. Replacing a worn or missing clip restores a snug fit and helps eliminate looseness, rattling, or misalignment.

• Holds a part, panel, tube, or wire securely in its mounting point
• Maintains alignment to prevent shifting or vibration
• Helps preserve proper fit and airflow when components are correctly seated
• Symptoms can include loose or sagging pieces, rattling noises, or parts that won't stay attached

• Unplug the refrigerator; if working near water lines, shut off the water supply
• Note the clip's orientation before removal; take a photo for reference
• Use needle-nose pliers to release/install; avoid over-flexing the clip
• After installation, tug-test gently to confirm a secure fit before reassembling