Magic Chef Refrigerator CSD2525ARA Ice maker won't dispense ice

The Replacement Icemaker is an OEM replacement part for Whirlpool made refrigerators including Whirlpool, Amana, Maytag, and many others. It is a component responsible for producing ice cubes or crushed ice, ensuring a constant supply of fresh ice for your convenience. Measuring approximately 11 inches long and 5 inches wide, this ice maker assembly is made of durable plastic and metal

Symptoms of needing a replacement icemaker include:

• No ice production or significantly reduced ice output
• Ice cubes appearing misshapen or clumped together
•  Leaks or water buildup in the icemaker area
• Strange noises or grinding sounds coming from the icemaker

Causes of a faulty icemaker can include normal wear and tear over time, water supply issues, clogging or blockages, or electrical malfunctions.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore refrigerator models.

Please note: that this ice maker is a replacement only and not suitable for add-ons or brand-new installations. It does not include the harness or hardware. For wire harness(Plug)order WPD7813010. For cover order WPW10289690. For shut off bail arm order WP67004028.

The Ice Door Fountain Kit is an OEM replacement part for Whirlpool refrigerators with built-in ice makers. It directs water to the ice molding trays and facilitates automated ice cube harvesting. Kit includes flapper, solenoid, strike arm, solenoid plunger, and instructions. Spring is not included. For the spring order 61004388.

Causes of a bad ice door fountain kit can include wear and tear over time, buildup of ice or debris obstructing the door mechanism, or damage to the components from frequent use.

Symptoms include:

• Incomplete ice cubes or low ice yield
• Drips or leaks in the ice maker area
• The ice drawer fails to eject cubes fully

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

This ice enclosure is the molded housing for the refrigerator's ice compartment. It supports and protects the ice dispensing components and guides ice into the chute or bin, helping maintain proper alignment and smooth dispensing. What it does:

• Provides structural support for the ice bucket/auger and related dispenser components
• Helps guide ice from the compartment into the chute/bin to reduce spills and jams
• Aids in maintaining alignment and a consistent cold zone around the ice area
• Typical symptoms of failure: cracked/broken housing, ice bin won't seat securely, ice jams or intermittent dispensing, frost/ice buildup in the ice compartment

• One ice enclosure

• Disconnect power; remove the ice bin before service
• Note screw locations; detach the old enclosure and any connected clips or wiring
• Transfer any brackets or hardware from the original enclosure; reuse existing fasteners
• Mount the new enclosure without overtightening; restore power and verify normal dispensing

This ice door spring restores the closing tension on the dispenser chute door. Replacing a fatigued spring helps the flap seal properly after dispensing, reducing warm-air leaks that cause frost buildup and ice clumping around the chute. What it does:

• Provides return tension so the ice chute door closes after dispensing
• Helps maintain a tight seal to limit frost, condensation, and air leaks
• Can resolve a chute door that sticks open/closed or won't fully close
• Reduce rattling or poor ice flow caused by a loose flapper

• 1 spring

• Disconnect power to the refrigerator before servicing
• Remove dispenser trim/control panel to access the ice door assembly
• Note spring orientation on the flapper; transfer/install carefully without over-bending
• Smooth flap movement and a proper seal before reassembly

• Dispenser door spring
• Flapper spring
• Ice chute door spring

The Icemaker Cycling Thermostat is an OEM part for Whirlpool refrigerators. This thermostat plays a crucial role in the icemaker's operation by monitoring the temperature in the icemaker and ensuring it is at the appropriate level for proper ice production. It reads the temperature to determine when the icemaker should cycle on and off.

Causes of a bad icemaker cycling thermostat can include electrical malfunctions, temperature sensor issues, or wear and tear.

Symptoms of a bad icemaker cycling thermostat may include:

• Inconsistent ice production.
• The icemaker not cycling properly.
• The icemaker not dumping the ice into the ice bin.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This icemaker fill cup and bearing assembly directs water from the inlet tube into the ice mold and provides the pivot point for the shutoff arm. Replacing a cracked or missing cup helps stop leaks, misdirected fills, and inconsistent ice production.

• Channels incoming water into the ice mold to prevent splashing and overfilling
• Provides the pivot/bearing for the ice level (shutoff) arm
• Helps maintain consistent cube size and reliable icemaker shutoff
• Typical symptoms: water or ice buildup under the icemaker, overfilling or hollow/irregular cubes, or a loose/binding shutoff arm

• Unplug the refrigerator and shut off the water supply before servicing
• Remove the ice bin and detach the icemaker to access the side-mounted cup
• Position the new cup directly under the fill tube; secure with existing hardware and verify the shutoff arm pivots freely in the bearing
• Restore power and water; run a test fill and check for leaks

This auger motor and yoke assembly powers the auger that moves ice from the freezer bin through the dispenser, restoring reliable ice delivery when the auger no longer turns or dispenses ice properly. What it does:

• Drives and supports the auger shaft that pushes ice to the dispenser chute
• Replaces a failed or noisy auger motor to restore normal ice dispensing
• Helps when the auger does not rotate, ice won't dispense, or the motor is unusually loud
• Interfaces with the dispenser gearbox/yoke to keep the auger aligned and turning

• One auger motor and yoke assembly

• Disconnect power to the refrigerator before beginning any work
• Remove the ice bin and any obstructing panels to access the auger assembly
• Handle parts and panels carefully—sharp edges may be present