Maytag Washer LAT8626ABE Leaking

The Mounting Stem Repair Kit is an OEM part for Whirlpool washing machines. It includes all necessary components to repair the mounting stem, which is a critical part of the washer's tub support system. Comes with the hub assembly, seal, and spanner nut. 6-2040130 should also be replaced at the same time. A spanner wrench is required to complete the repair TB123B.

Symptoms of a bad mounting stem include:

• Excessive noise or vibration during the spin cycle.
• The washer tub appearing loose or off-balance.
• Leakage around the central area of the washer, indicating a possible seal failure.

Causes of a bad mounting stem can include wear and tear from normal usage, especially with heavy loads, or corrosion and material fatigue that weaken the stem's integrity.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Tub Bearing Kit is an OEM part for Whirlpool washers. It includes all the necessary components to replace the tub bearing which is responsible for supporting the inner tub and allowing it to spin smoothly during the wash cycle. Over time, the bearing may wear out or become damaged, leading to excessive noise, vibrations, or even leaks from the washer.

Causes of a bad tub bearing can include regular wear and tear, exposure to heavy loads or unbalanced loads that put excessive strain on the bearing, or damage due to water leaks.

Symptoms of a bad tub bearing include:

• Excessive noise or grinding during the wash cycle.
• Vibrations or shaking of the washer.
• Leaks from the washer, around the tub area.
• The inner tub not spinning or becoming stuck.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Note: It is advised to replace the Mounting Stem Repair Kit, part number 6-2040130 at the same time.  To complete the repair, you’ll also need a Spanner Wrench to complete the repair (TB123B).

The Washer Drain Pump is an OEM part for Whirlpool washing machines. It is responsible for removing water from the washing machine during the drain cycle, ensuring efficient and complete water removal.

Causes of a bad drain pump can include blockages from debris or foreign objects, electrical failures, or wear and tear from regular use. Over time, these issues can impede the pump's ability to function properly.

Symptoms of a bad drain pump include:

• Water not draining from the washer
• Unusual noises during the drain cycle
• Error codes related to draining issues
• Leaks coming from the pump area

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Note: Fits 2 belt design Maytag washers. Check belts for wear; if needed order 12112425.

The Tub to Pump Hose is an OEM part for Whirlpool washing machines. This hose connects the tub to the pump, allowing water to drain from the tub during the washing and rinsing cycles. It is designed to handle the water flow and pressure within the washer, ensuring efficient drainage.

Causes of a bad tub to pump hose can include wear and tear over time, exposure to harsh chemicals or debris, or damage due to accidental punctures or kinks. When the hose is compromised, it can lead to drainage issues and potential water leaks.

Symptoms of a bad tub to pump hose include:

• Water not draining from the washer
•  Leaks or puddles underneath the washer
• Visible cracks or wear on the hose
• Error codes related to drainage problems

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.

Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Water leaks around the hose connection points
• The hose slipping off the fitting
• Visible rust or wear on the clamp
• Difficulty in tightening the clamp to secure the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

The Tub Cover Gasket is an OEM part for Whirlpool washing machines. This part creates a watertight seal between the tub cover and the tub, preventing water from leaking during the wash cycle. 

Causes of a bad gasket include exposure to harsh detergents, regular wear and tear, or improper installation. 

Symptoms of a bad tub cover gasket include:

• Water leaking from the washing machine
• Excessive moisture around the tub cover area
• Visible cracks or wear on the gasket
• Unusual noises during the wash cycle due to improper sealing

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This tub cover and gasket seal the top of the outer tub to contain splashing and prevent leaks during wash and spin. Replacing a cracked cover or compressed gasket restores a tight rim seal and cleaner operation. What it does:

• Creates a watertight seal at the outer tub rim
• Helps reduce splash-over and directs incoming water flow
• Helps keep clothing and debris out of the gap between basket and outer tub
• Common symptoms: leaks from the top/front, visible cracks in the ring, or a brittle/torn gasket

• One tub cover and one perimeter gasket

• Disconnect power and turn off the water supply before servicing
• Access the tub area; release retaining clips/screws and detach any inlet/flume from the old cover
• Clean the tub rim thoroughly; seat the new gasket evenly and install the cover without pinching the seal
• Reuse existing fasteners/clips; ensure the cover is fully latched all around and do not overtighten

This rubber seal creates a tight barrier between mating components to keep water contained and stop drips. Replacing a flattened or cracked seal helps prevent leaks and protects nearby parts from moisture-related damage. What it does:

• Forms a watertight gasket between two parts in the assembly
• Helps prevent drips or seepage at the connection point
• Restores proper compression when the original seal hardens or deforms
• Common signs of failure: leaks, dampness, or visible cracking/flattening of the old seal

• 1 rubber seal

• Disconnect power; for water-bearing assemblies, shut off the water supply
• Access the seal location per your service information and note orientation/depth before removal
• Clean mating surfaces; lightly moisten the new seal with water or mild soap to ease installation
• Ensure the seal is fully seated, reassemble, and test for leaks

This hose clamp secures a rubber or plastic hose to its fitting to maintain a tight, leak-resistant seal. Replace a worn or missing clamp to stop drips and keep appliance water connections secure.

• Fastens a hose to a barb or port to prevent leaks
• Helps keep hoses from slipping off due to vibration or pressure
• Restores proper sealing when a clamp is rusted, bent, or stripped
• Common symptoms: water dripping at a hose joint, loose hose connection, or a clamp that won't tighten

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water when removing hoses
• Position the clamp just behind the hose barb/bead and secure with the appropriate tool
• Restore water and power, then run a quick check for leaks at the connection

This retaining washer secures a center-mounted component within the assembly, keeping parts aligned and in place during operation. Replacing a worn or missing washer helps prevent looseness, vibration, and noise for more reliable performance. What it does:

• Holds a component on a center shaft or stud to prevent axial movement
• Maintains proper alignment under rotation and load
• Can reduce wobble, rattling, or scraping noises from a shifting assembly
• In applicable washers, can help restore consistent agitation or spin when parts have been moving out of place

• 1 retaining washer

• Disconnect power and water before servicing; wear cut-resistant gloves
• Note the order and orientation of all spacers, washers, and clips during disassembly
• Clean mating surfaces and ensure the washer is fully seated before reassembly
• Inspect adjacent hardware for wear or damage and replace as needed

This small clamping nut secures a mating clamp or bracket so the connected component stays firmly in place. Replacing a worn, stripped, or missing nut restores a solid hold and helps prevent looseness or leaks around the secured area.

• Secures a clamp or bracket to its mounting point
• Restores proper clamping force when the original nut is stripped or missing
• Common signs: loose clamp, rattling/vibration, clamp won't tighten, minor leaks where the clamp is used
• Durable hardware replacement to maintain stable, reliable assemblies

• Disconnect power and shut off water/gas to the appliance before service
• Note clamp/bracket orientation before removal for correct reassembly
• Start threads by hand to prevent cross-threading; then tighten with the appropriate tool
• Do not overtighten—snug just enough to securely clamp the component

This top-load washer agitator shaft collar fits on the drive shaft to locate and secure the agitator. Replacing a worn collar restores proper alignment and engagement, reducing wobble and helping maintain consistent wash action.

• Positions the agitator at the correct height on the drive shaft
• Helps ensure positive engagement so the agitator moves as designed
• Maintains alignment to minimize excess play and noise
• Common symptoms of a failed collar: loose or wobbly agitator, rattling/knocking during wash, weak or intermittent agitation

• Disconnect power and water supply before servicing
• Remove the agitator to access the collar; note the original position for reference
• Install and secure the new collar per the manufacturer procedure; verify proper alignment and minimal play
• Reinstall the agitator and run a brief test to confirm smooth operation

This bleach dispenser tube channels liquid bleach from the dispenser cup into the washer tub during the cycle. Replacing a cracked or clogged tube helps prevent leaks and ensures bleach is delivered properly to the wash.

• Directs bleach from the dispenser to the tub during the flush/fill cycle
• Helps contain corrosive bleach to protect the cabinet and internal parts
• Common failure signs: water/bleach leaking near the dispenser area, bleach remaining in the cup, brittle/cracked tubing, or bleach odors/stains around the cabinet
• Restores proper bleach flow and dispensing performance

• Disconnect power and water; wear gloves and eye protection when handling bleach
• Access the dispenser/tube by lifting the top or console per service procedures
• Place a towel for residual liquid; remove spring clamps and transfer/reuse if in good condition
• Route the new tube exactly like the original, avoid kinks, seat fully on fittings, secure with clamps, and test for leaks