Parts for Ge AEC18DYL1: Room Air Conditioner Parts

This nut-washer secures appliance assemblies where a captive nut and flat washer are needed, helping keep fasteners tight during normal operation. It's a small replacement part that prevents loosening and maintains proper component alignment. What it does:

• Acts as a combined nut and washer to fasten components and distribute load
• Keeps threaded connections from backing off due to vibration
• Restores secure attachment when the original nut-washer is damaged, stripped, or missing
• Commonly replaced when assemblies wobble, rattle, or come loose

• One nut-washer

• Disconnect power and unplug the appliance before beginning any repair
• Use the proper screwdriver or socket to avoid rounding the fastener
• If threads are damaged, replace the mating screw or stud rather than over-tightening

A small flat washer used as a replacement fastening spacer that helps secure bolts and prevent metal-to-metal wear. Restores proper spacing and fastener tension so assemblies stay aligned and tight. What it does:

• Acts as a spacer and load-distribution surface under a bolt or nut
• Prevents fasteners from loosening and reduces metal wear at contact points
• Restores correct alignment where a missing or worn washer caused vibration or rattling
• Simple, durable replacement for worn or corroded washers in mechanical assemblies

• Disconnect power before servicing electrical appliances to avoid shock
• Use appropriate hand tools; replace with the same style and thickness for correct fit
• Inspect mating fasteners and surfaces; replace any damaged hardware

This 10 mm-diameter gasket provides a precise seal to prevent leaks and maintain proper operation of the appliance connection where it installs. Durable construction helps restore a tight, reliable seal. What it does:

• Creates a watertight/airtight seal at the mating joint to prevent leaks
• Helps maintain proper pressure and function of the connected component
• Replaces worn, cracked or flattened seals that can cause drips or loss of performance
• Restores reliable sealing to reduce cycling or moisture-related issues

• Disconnect power and shut off water supply before starting any repair
• Inspect mating surfaces and clean away residue to ensure a proper seal
• Replace the old gasket fully; do not stretch excessively when installing
• After installation, restore power/water and check the connection for leaks

This spring washer provides resilient tension to help keep screws and bolts from loosening on appliance assemblies. It's a simple replacement part that restores proper fastener tension and helps maintain secure connections. What it does:

• Applies spring force around a fastener to resist vibration-related loosening
• Commonly used on panels, brackets, and components that see movement or vibration
• Can reduce rattling and intermittent connection issues caused by loose hardware
• Works with 6 mm-diameter fasteners where a small lock-style washer is required

• Disconnect power and unplug the appliance before servicing
• Use the correct 6 mm fastener and proper orientation when reinstalling
• Tighten hardware to the OEM's recommended torque if available; avoid overtightening
• If other fasteners or parts are damaged, replace them to ensure a secure repair

A small mounting nut used to secure components and panels on compatible appliances. Replaces a loose or missing nut to restore stable, safe fastening and reduce rattling or wobble. What it does:

• Secures panels, brackets, or assemblies to the appliance frame
• Prevents fasteners from backing out during normal operation
• Helps stop rattling, vibration noise, and loose-fitting parts
• Restores proper alignment for attached components

• Disconnect power and water before beginning any repair
• Match threads and size before installation; hand-start the nut to avoid cross-threading
• Tighten securely with the correct socket or wrench, but do not overtighten
• If the original fastener was damaged, replace the mating bolt/stud as needed

The Axial Flow Fan is an OEM part for GE air conditioners responsible for circulating air within the air conditioner unit, ensuring proper airflow and efficient cooling performance.

A bad axial flow fan can be caused by motor issues, damage to the fan blades, or wear and tear over time. If you experience reduced airflow, unusual noises coming from the air conditioner, or poor cooling performance, it may indicate a problem with the axial flow fan.

Symptoms of a bad axial flow fan include:

• Reduced or weak airflow from the air conditioner
• Unusual noises from the unit
• Uneven cooling or difficulty reaching the desired temperature
• Overheating of the air conditioner unit

Replace your faulty axial flow fan with this genuine OEM part to restore airflow on your air conditioner. This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This 8 mm diameter gasket creates a reliable seal in appliance assemblies to help prevent leaks and loss of pressure or airflow. It's a small replacement part that restores proper sealing where a worn gasket is causing issues. What it does:

• Seals joints and connections to help prevent water or air leaks
• Restores tight fit where a cracked, brittle, or flattened gasket allows seepage
• Reduces vibration noise from loose or poorly sealed parts
• Helps maintain proper operation of the sealed compartment or fluid path

• One 8 mm diameter gasket

• Disconnect power and water supply (when applicable) before servicing the appliance
• Remove old gasket and thoroughly clean mating surfaces before installing the new gasket
• Ensure the gasket is fully seated and aligned along the entire contact surface for an effective seal

A small circular rubber gasket designed to provide a reliable seal where a 8 mm diameter gasket is specified. Helps prevent air, moisture, or dust from passing through a joint or opening in the appliance. What it does:

• Creates a tight seal around shafts, openings, or mating surfaces to reduce leaks and drafts
• Cushions and protects components from vibration and wear
• Helps maintain correct airflow or pressure paths inside the appliance
• Common replacement when a worn or cracked seal causes unwanted noise, moisture, or air loss

• One 8 mm diameter gasket

• Inspect mating surfaces and clean thoroughly before installing the new gasket
• Replace only with the exact gasket size specified for your appliance to ensure proper sealing
• If adhesive or a retainer is used, follow the appliance manufacturer's instructions for secure attachment
• Disconnect power or follow appliance safety procedures before servicing

This M8 nut secures components to an M8 stud or bolt, restoring a firm mechanical connection. Use it to replace a missing, stripped, or loose fastener so panels and brackets stay properly attached. What it does:

• Threads onto an M8 bolt or stud to lock parts together.
• Prevents components from working loose due to vibration.
• Commonly used on brackets, mounts and assemblies that require an M8 fastener.
• Replacing a worn or missing nut can stop rattling, movement, or misalignment.

• Disconnect power and follow appliance safety procedures before servicing.
• Use the correct sized wrench or socket to avoid rounding the nut.
• Tighten to the manufacturer's recommended torque where available; do not overtighten.
• Inspect mating bolt/stud threads and replace if damaged.

This curtain quickset is a small mounting clip that secures the appliance's inner curtain/trim so panels and seals stay aligned for proper fit and quiet operation. It restores correct positioning after wear or damage. What it does:

• Secures the inner curtain/trim to the door or frame to maintain proper alignment
• Prevents rattling, gaps, or uneven panel fit that can affect sealing and appearance
• Keeps adjacent trim pieces from shifting during normal use
• Helps restore factory fit after a broken or missing clip

• Disconnect power or gas to the appliance before beginning any work.
• Handle surrounding trim and glass carefully to avoid damage; small fasteners can be sharp.
• Basic hand tools may be required; follow the appliance service manual for removal/installation steps.

This top guide secures and aligns the appliance's upper panel or cooktop, helping smooth movement and stable positioning. It restores proper fit and reduces rattling or misalignment for a safer, more reliable top surface. What it does:

• Guides and supports the appliance top or panel to maintain correct alignment
• Reduces noise and movement caused by a loose or worn guide
• Helps prevent gaps that can trap debris or affect surface stability
• Works as a direct-fit replacement for the original guide to restore intended function

• Disconnect power and any fuel sources before starting repairs
• Access the guide by removing the top/panel per the appliance service instructions
• Inspect adjacent clips, screws, and mounting points and replace if damaged

This molded form gasket provides a replacement seal designed to restore a tight closure and reduce air or water leakage. It helps maintain proper appliance operation by replacing a worn or damaged seal. What it does:

• Seals the mating surface to prevent air or water from leaking out
• Helps reduce frost build-up or moisture-related pooling when the seal is compromised
• Restores door/compartment closure where a deformed or torn gasket allows gaps
• Commonly replaced when gasket shows visible cracks, gaps, or continual leaks

• Disconnect power and remove any stored items before replacing the gasket
• Clean and dry the sealing surface thoroughly to ensure a proper fit
• Align the gasket into the channel and press evenly; some trims may require careful seating along the entire edge
• Inspect surrounding trim and hardware; replace or tighten as needed for a complete seal

This Form Gasket 2 is a replacement sealing gasket designed to restore a tight, reliable seal where the original foam/form gasket has become compressed or damaged. Replacing it helps reduce leaks and maintain normal appliance operation. What it does:

• Replaces a worn or damaged foam/form gasket to restore proper sealing
• Helps prevent water, air, or debris from passing where the original gasket seals
• Commonly used where a formed seal cushions or closes a gap in the appliance assembly
• Address symptoms such as visible gaps, leaks, rattling, or improper sealing along the joint

• One Form Gasket 2 as shown

• Install in clean, dry area; remove old gasket and clean mating surfaces before fitting the new gasket
• Fit gasket to the formed channel or mounting surface per the appliance's service instructions
• Wear gloves to protect hands from sharp edges and to avoid contaminating the gasket surface

This accordion panel seal replaces the flexible gasket that seals the appliance cabinet panel, helping keep the cabinet closed and reducing drafts, dust, and vibration noise around the panel area. What it does

• Replaces worn or torn accordion-style gasket on the cabinet/panel edge
• Restores a snug seal to reduce drafts and prevent dust or lint from escaping
• Reduces panel vibration and rattling caused by loose or damaged seals
• Helps maintain proper airflow routing by sealing the cabinet opening

• Disconnect power to the appliance before beginning any repair
• Removal of the front or cabinet panel is typically required; keep fasteners organized
• Handle edges and clips carefully—use proper tools to avoid damaging the seal or cabinet
• Follow OEM disassembly/reassembly instructions

This foam insulation replaces worn or missing cabinet insulation to help reduce heat transfer and dampen noise for proper appliance performance. It fits into the cabinet cavity to support consistent temperatures and quieter operation. What it does:

• Adds thermal cushioning to slow unwanted heat or cold transfer
• Helps reduce operational noise and vibration from internal components
• Contributes to more stable internal temperatures for better efficiency
• Prevents direct contact between metal components to reduce rattling

• One foam insulation piece as pictured

• Install in a clean, dry cabinet cavity following OEM placement and orientation
• Use gloves to avoid skin irritation from foam fibers; avoid compressing or tearing the material
• If adhesive or clips are used, replace with OEM-recommended fasteners only
• Disconnect power and follow all safety instructions for your appliance before servicing

This capacitor clamp is a small metal bracket that secures a refrigerator or appliance capacitor to the cabinet, helping keep the capacitor stable and preventing movement or vibration during operation. It preserves reliable electrical connections and reduces noise from loose components. What it does

• Holds the capacitor firmly in place to prevent shifting and rattling
• Helps maintain stable capacitor connections to avoid intermittent motor or control issues
• Reduces vibration-related noise from the capacitor area
• Protects the capacitor from contact with other components that could cause wear or damage

• One capacitor clamp/mounting bracket

• Disconnect power before accessing electrical components
• Inspect the clamp for cracks, corrosion, or missing fasteners and replace if damaged
• Retain original mounting hardware when possible; use compatible screws or bolts if replacements are needed

This thermostat is the temperature control for room air conditioners. It senses temperature and cycles the compressor to maintain your set comfort level, helping restore consistent cooling when the original control becomes inaccurate or fails. What it does:

• Monitors temperature and opens/closes contacts to start and stop the compressor
• Helps the unit reach and maintain the temperature you select
• Helps resolve symptoms such as: AC won't turn on/off at the dial setting, runs continuously, short-cycles, or temperature adjustments have little effect
• Direct-fit replacement designed for the original mounting location

• 1 thermostat

• Disconnect power before servicing to avoid electrical shock
• Access the control panel; note wire locations and transfer any mounting hardware from the old part
• If your model uses a capillary sensing tube, route it exactly as original and secure in clips; do not kink or sharply bend it
• Reassemble, align the control knob, and test operation across several temperature settings

The Display Circuit Board is an OEM part for GE window air conditioners. Mounted on the front of the unit, it houses the screen responsible for indicating settings and operation status.

Causes of a faulty display board can include damage from excessive impact or abrasion over time. Failure of onboard LED lights and digit technology due to prolonged heat and power cycling. 

Symptoms include: 

• Blank or illegible control screen readout   
• Inoperative buttons with no feedback  
• Loss of unit programming upon power losses
• Display fading, flickering or non-responsiveness

This genuine GE replacement helps maintain convenient usability and programming capabilities. Compatible with some Honeywell, Friedrich, and EdgeStar branded units, it enhances the user experience. 

This replacement power cord restores electrical connection to compatible GE appliances so the unit powers on safely and reliably. Use it when the original cord is damaged, frayed, or no longer providing consistent power. What it does:

• Replaces a worn or damaged mains cord to restore power to the appliance
• Stops issues caused by frayed wires, exposed conductors, or loose connections
• Helps eliminate intermittent power, arcing at the plug, or visible cord damage
• Works as the direct electrical connection between the appliance and household outlet

• Always unplug the appliance or shut off breaker power before servicing
• Basic hand tools may be required to remove access panels and secure wiring terminals
• Confirm cord orientation and terminal connections match the original; tighten terminals firmly

This sensor support is a small mounting bracket that secures an appliance sensor in the correct position for reliable readings and consistent operation. It replaces a worn or broken bracket to restore proper sensor placement. What it does:

• Holds the sensor firmly in place to help maintain accurate measurements
• Prevents sensor movement or vibration that can cause inconsistent readings
• Helps reduce false error codes related to misaligned sensors
• Restores proper sensor positioning after accidental damage or wear

• One sensor support mounting bracket

• Disconnect power to the appliance before beginning any repair
• Handle the sensor and wiring gently; avoid pulling on wires or connectors
• Ensure the sensor is seated in the bracket in the correct orientation before reassembly
• Use the existing fasteners or clips; do not overtighten plastic parts