Parts for Ge AEE12DTL2: Room Air Conditioner Parts

This flat washer provides a secure, even load distribution for a fastener on the appliance, helping maintain proper assembly and reduce loosening or wear. Use it to replace a damaged or missing washer during repairs. What it does:

• Sits under a nut or bolt to spread load and protect the appliance surface
• Helps prevent fasteners from loosening due to vibration
• Restores proper spacing and alignment for connected parts
• Commonly replaced when you see corrosion, cracking, or a loose connection

• One flat washer

• Disconnect power and turn off water supply before starting any repair
• Tighten fasteners to a snug fit—avoid over-tightening which can crush the washer
• If adjacent parts show damage or corrosion, inspect and replace as needed

This nut with attached washer is a small securing fastener used to clamp appliance parts and prevent loosening. It provides a low-profile, integrated washer bearing surface for a reliable hold. What it does:

• Secures panels, brackets, or components to prevent movement and rattling
• Maintains clamping force where an integrated washer is needed
• Helps keep electrical and mechanical connections stable
• Common symptom: loose or vibrating parts, squeaks, or components that shift during use

• One nut with attached washer

• Disconnect power and water before servicing
• Use the correct socket or wrench to avoid rounding the nut
• Tighten to snug fit — avoid overtightening which can strip threads or damage parts
• If replacing a rusted or damaged fastener, inspect mating threads and replace as needed

This spring washer provides resilient tension to help keep screws and bolts from loosening on appliance assemblies. It's a simple replacement part that restores proper fastener tension and helps maintain secure connections. What it does:

• Applies spring force around a fastener to resist vibration-related loosening
• Commonly used on panels, brackets, and components that see movement or vibration
• Can reduce rattling and intermittent connection issues caused by loose hardware
• Works with 6 mm-diameter fasteners where a small lock-style washer is required

• Disconnect power and unplug the appliance before servicing
• Use the correct 6 mm fastener and proper orientation when reinstalling
• Tighten hardware to the OEM's recommended torque if available; avoid overtightening
• If other fasteners or parts are damaged, replace them to ensure a secure repair

A small mounting nut used to secure components and panels on compatible appliances. Replaces a loose or missing nut to restore stable, safe fastening and reduce rattling or wobble. What it does:

• Secures panels, brackets, or assemblies to the appliance frame
• Prevents fasteners from backing out during normal operation
• Helps stop rattling, vibration noise, and loose-fitting parts
• Restores proper alignment for attached components

• Disconnect power and water before beginning any repair
• Match threads and size before installation; hand-start the nut to avoid cross-threading
• Tighten securely with the correct socket or wrench, but do not overtighten
• If the original fastener was damaged, replace the mating bolt/stud as needed

This thermostat is the temperature control for room air conditioners. It senses temperature and cycles the compressor to maintain your set comfort level, helping restore consistent cooling when the original control becomes inaccurate or fails. What it does:

• Monitors temperature and opens/closes contacts to start and stop the compressor
• Helps the unit reach and maintain the temperature you select
• Helps resolve symptoms such as: AC won't turn on/off at the dial setting, runs continuously, short-cycles, or temperature adjustments have little effect
• Direct-fit replacement designed for the original mounting location

• 1 thermostat

• Disconnect power before servicing to avoid electrical shock
• Access the control panel; note wire locations and transfer any mounting hardware from the old part
• If your model uses a capillary sensing tube, route it exactly as original and secure in clips; do not kink or sharply bend it
• Reassemble, align the control knob, and test operation across several temperature settings

This PCB support is a molded mounting bracket that holds the appliance control board securely in place to prevent movement and contact with other components. It helps maintain reliable electrical connections and reduces board stress during operation. What it does:

• Secures the control printed circuit board to the chassis or housing to prevent vibration or dislodging
• Keeps the PCB spaced from metal parts to reduce shorting or abrasion risk
• Helps maintain stable connector engagement to avoid intermittent electrical faults
• Commonly replaced when the original support is cracked, broken, or missing

• Disconnect power to the appliance before starting any repair to avoid shock or damage
• Handle the PCB and support carefully; avoid bending the board or stressing solder joints
• Use appropriate fasteners; replace any damaged clips or screws with OEM-specified hardware

This inline refrigerator water filter removes sediment and common impurities from your fridge's water supply to help improve water clarity and taste. It installs in the water line and provides a simple, replaceable filtration point. What it does:

• Filters out sediment and particulate matter that can make water appear cloudy
• Helps reduce common tastes and odors caused by chlorine and organic compounds
• Can improve ice clarity and flavor when installed on the refrigerator water feed
• Resolve symptoms like reduced water taste quality, cloudy ice, or unusual water odor

• One inline refrigerator water filter cartridge

• Turn off the refrigerator water supply and relieve line pressure before replacing
• Follow the refrigerator manufacturer's instructions for disconnecting and reconnecting the water line
• Flush several gallons of water through the filter after installation to clear trapped air and loose carbon fines
• Inspect fittings for leaks after installation and tighten as needed