Parts for Ge AEE18DTL3: Room Air Conditioner Parts

This front panel assembly replaces the damaged or worn control/display bezel on compatible GE appliances, restoring the unit's user interface and appearance. It provides the mounting surface and openings for the control buttons and display. What it does:

• Replaces cracked, faded, or broken front bezel and restores button/display access
• Secures and aligns the control board and user interface components
• Helps resolve issues where buttons are hard to press or the front is cosmetically damaged
• Keeps internal controls protected from spills and debris

• Installation requires removing the appliance outer housing and disconnecting power first; unplug or switch off breaker before starting.
• Handle with care to avoid scratching the finished surface and to protect attached cables and clips.
• Reuse original fasteners unless replacements are specified by the manufacturer.
• If the control board or display components are damaged, this panel replaces only the outer/front assembly.

This is the air filter assembly for select GE room air conditioners. It traps dust and lint before they reach the evaporator coil, helping maintain airflow and cooling performance.

• Captures airborne dust and lint to protect the coil and blower
• Helps maintain steady airflow and cooling efficiency
• Replace if cracked, warped, missing, or won't stay seated
• Common symptoms include reduced airflow and visible debris on the filter

• Unplug the unit before servicing
• Remove the front grille or filter access panel; slide the old filter out
• Install the new filter with airflow orientation matching the original
• Clean surrounding surfaces and reinstall grille before powering on

This display board is the electronic control/display assembly that powers the oven/range user interface, restoring visible status, clock and touch controls so the appliance responds normally to settings and timer functions. What it does:

• Powers and displays clock, temperature and cycle information on the front control panel
• Receives input from the touchpad/buttons and sends control signals to the range/oven control system
• Common fix for unlit or scrambled displays, non-responsive front controls, or missing clock/timer readouts
• Helps eliminate intermittent or incorrect display messages caused by a failed display/control board

• One display board / control/display assembly (as shown)

• Disconnect power (unplug or shut off breaker) before beginning any service
• Handle the board by the edges; avoid touching components and use anti-static precautions if available
• Carefully disconnect ribbon cables and connector harnesses; note connector locations for reassembly

This fan motor drives the convection blower in the oven to circulate hot air for even cooking and faster preheating. Replacing a worn motor restores proper airflow and helps improve bake and roast performance. What it does:

• Spins the convection blower to circulate hot air throughout the oven cavity
• Helps maintain consistent oven temperature and reduce hot spots
• Commonly replaced when the oven has uneven cooking, weak airflow, or loud/grinding noise from the fan
• Also needed if the fan fails to run or stops intermittently during operation

• One fan motor

• Disconnect power at the breaker before servicing the oven to avoid shock hazard
• Verify rotation direction and mounting orientation before final reassembly
• Inspect blower wheel and mounting hardware; replace any damaged components for proper fit

This axial flow fan moves air through the appliance to help cool internal components and support proper airflow. Replacing a worn or damaged fan restores quiet operation and helps prevent overheating-related issues. What it does:

• Circulates air across internal components or heat exchangers to maintain proper operating temperatures
• Helps prevent overheating of electronics, motors, or heating elements
• Reduces abnormal noise caused by worn or imbalanced fan blades or bearings
• Supports consistent airflow for reliable appliance performance

• One axial flow fan assembly

• Disconnect power to the appliance before starting any repair
• Handle the fan blades carefully to avoid damage; align properly during installation
• Verify secure mounting and electrical connections before restoring power
• Test appliance operation after installation and observe for proper airflow and quiet operation

This is a replacement power cord that restores safe electrical connection to the appliance. Use it when the original cord is damaged or no longer supplying reliable power to help restore normal operation. What it does:

• Provides the main electrical connection between the appliance and household power
• Replaces frayed, cut, or melted cords that cause intermittent power or no power
• Removes loose or damaged plug connections that can trip breakers or cause arcing
• Helps eliminate visible burn or scorch marks at the cord or plug

• Always disconnect power at the breaker or unplug the appliance before servicing.
• Verify the cord routes through the strain-relief and is secured per the appliance's wiring harness.
• Inspect terminal connections for corrosion and tighten securely; match wire colors to original wiring.

This indoor air thermistor is a refrigerator air temperature sensor that helps the control board monitor cabinet temperature for proper cooling performance. Replacing a failing thermistor restores accurate temperature sensing to help prevent spoilage and cycling issues. What it does:

• Senses interior air temperature and sends temperature signals to the fridge control board
• Helps the compressor and fans run at the correct times for stable cooling
• Commonly associated with symptoms like warm or fluctuating temperatures, excessive cycling, or cooling that never reaches the set point
• Works as part of the temperature control system—faulty sensors can cause incorrect defrost or cooling behavior

• Disconnect power to the appliance before accessing or replacing the sensor
• Handle the sensor lead and element carefully to avoid damage; avoid pulling on wires
• Reinstall in the original location and routing; secure connectors fully to ensure good electrical contact

The electronic main control board that manages refrigerator functions and user controls, restoring proper communication between sensors, the display and the compressor system for reliable cooling and operation. What it does:

• Controls and coordinates temperature regulation, defrost cycles and compressor run times.
• Processes inputs from the control panel and sensors to run cooling and ice/water features.
• Symptoms of a failing board may include a blank or unresponsive display, no cooling or irregular cooling cycles, or unreachable controls.
• Replacing the board can resolve intermittent operation and communication faults when other components test good.

• Disconnect power before starting to avoid shock or component damage.
• Handle the board carefully to avoid electrostatic discharge; ground yourself or use an ESD strap.
• Verify model and part number on the existing board before ordering and match connector locations during installation.

This top guide secures and helps align the dishwasher's upper rack for smooth sliding and reliable operation. It prevents the rack from binding or coming off the track, restoring normal loading and unloading performance. What it does:

• Guides and stabilizes the upper rack as it moves in and out
• Keeps the rack properly aligned to prevent tipping or jamming
• Reduces wear on the rack rollers and track by maintaining correct alignment
• Helps ensure dishes load and unload smoothly without shifting

• One top guide

• Designed for straightforward replacement; remove the upper rack to access the guide
• Inspect the track and rollers for damage and clean before installing
• Use basic hand tools; avoid forcing plastic tabs to prevent breakage
• Disconnect power and follow appliance safety guidelines before servicing

This support to cabinet is a metal mounting bracket that secures the appliance to surrounding cabinetry for stable, rattle-free operation. It helps keep the unit aligned and prevents shifting or sagging during normal use. What it does:

• Anchors the appliance to the cabinet frame to maintain proper alignment and fit
• Reduces vibration and rattling caused by loose or worn fasteners
• Prevents the appliance from tilting or shifting when doors or controls are used
• Restores safe, stable mounting after damage or corrosion to the original bracket

• Disconnect power (and gas if applicable) and remove surrounding trim before starting
• Retain or replace mounting hardware as needed; use screws appropriate for cabinet material
• Position bracket squarely against cabinet and appliance mounting points, then tighten securely

This curtain assembly replaces a damaged or missing door trim curtain to restore proper fit and protect internal components while improving appearance. It's a direct-replacement component used on compatible GE appliances. What it does:

• Covers and protects internal door/frame openings to keep components shielded from debris and light
• Helps maintain correct door alignment and trim fit for smooth opening and closing
• Reduces rattling or vibrating noises caused by a loose or broken curtain piece
• Restores finished appearance when the original curtain is cracked, warped, or missing

• One curtain assembly

• Disconnect power to the appliance before starting any repair
• Installation typically requires removal of the outer door or trim panel and basic hand tools
• Handle parts carefully to avoid scratching trim or damaging clips; keep fasteners organized for reassembly